WilTec 62571 Operation Manual Download Page 11

Cleaning the air valves

The device should be kept clean in order to allow the air valves to cool the device and its motor.

Lubricating the connections

In order to ensure smooth and proper junctions and to keep o-rings from drying out, the junctions
should be lubricated regularly.

Troubleshooting

Problem

Possible cause

Potential solution

The device does not
start

Device is not connected to
the mains supply

Malfunctioning   socket-out-
let

Fuse has blown

Damaged extension cord

Connect the device

Try another socket-outlet

Replace the fuse

Disconnect other devices

Replace the extension cord or try
operate the device without

Pressure   fluctu-
ations

Pump draws air

Valves are dirty, blocked or
worn 

Insufficient water supply

Pump seal is worn

Check   impermeability   of   hoses
and connections 

Increase   the   water   pressure,
check   for   blockage   and/or   ex-
change the hose

Consult a qualified expert

The device stops its
operation

Fuse has blown

Incorrect line voltage

Overheating   protection   is
active

Partially clogged nozzle

Replace the fuse

Disconnect other devices

Check if voltage conforms to the
nameplate of the device

Device needs to cool down for 5 
minutes

Clean the nozzle with a needle

Fuse has blown

Fuse is too small

Increase of amperage 

Replace with a sufficient fuse

Try   operating   without   extension
cord

Device sputters

Air inside the hose/pump

Insufficient water supply

Partially blocked water jet

Water filter is clogged

Buckled hose

Pull the trigger to release air until
the air has been drained

Increase   the   water   pressure,
check   for   blockage   and/or   ex-
change the hose

Clean the nozzle with a needle

Clean the filter

Unfold the hose

Device turns on and
off on its own

Fuse or pump control mal-
functions

Insufficient water supply

Consult a qualified expert

Connect to sufficient water supply

Device   is   running,
but   no   water   is   re-
leased

Dirty or clogged water filter

Blocked nozzle

Clean the water filter

Clean the nozzle with a needle

© by WilTec Wildanger Technik GmbH 

Item 62571

Page 11 

http://www.WilTec.de
http://www.aoyue.eu

 

11 2020

-1

http://www.teichtip.de

Summary of Contents for 62571














Reviews: