WilTec 62571 Operation Manual Download Page 10

1. Mount the sprayer fixture (Fig. 1, A) as well as the guide bar (Fig. 1, B) to the side of the pres-

sure washer frame.

2. Place the sprayer (Fig. 2, C) on the fixture (Fig. 1, A) and attach the jet pipe (Fig. 2, D) to the

guide bar (Fig. 1, B)

3. Attach the cable bracket (Fig. 3, E) to the device by sliding it into the mounting rail (Fig. 3, F)

located at the back of the device.

4. Remove the locking cap of the cleaning agent tank (Fig. 4, G) and insert appropriate cleaning

agents. Close the tank after filling it and make sure that it is closed properly and that liquids do
not leak from it.

Storage

The device should always be stored in a frost-protected environment!

The pump, hose and accessories should always to be freed from residual water before the device is
being stored. Abide by the following steps in order to successfully free the device of residual water:

Stop the operation by setting the power switch into the “0” position and carefully remove the
pressure and water supply hoses from the device, as well as the nozzle from the sprayer.

Restart the device and pull the sprayer trigger. Keep it pulled until water stops flowing through
the sprayer.

Stop the device, disconnect it from the mains supply and carefully roll up the cable and hose.

Clean all the accessories and properly dry them.

Store them in their respective holders.

Warning: 

Never use the device in a freezing environment or after it has been exposed to such an en-

vironment and low temperatures before. In this case allow the device to acclimatise properly before
putting it to use.

Maintenance

Warning!

 Always make sure to disconnect the device from the mains supply before performing clean -

ing, repairs or maintenance wok. 

Consider the following notes in order to ensure the functionality of the device and to prolong its service
life:

Rinse the pressure and water hoses as well as the jet pipe and other accessories with clear
water before assembling the device.

Clean the nozzle as well as all junctions in order to remove dust and sand. It is further advised
to rinse the hoses with clean water after every use.

Repairs should only be performed by qualified experts and spare parts should be authorised
parts of equal quality.

Cleaning the internal filter

1. 

Make sure to clean the filter at least once a month and more often if the device is used frequently.

2. 

Carefully remove the filter with help of a screw driver and clean it. Make sure to check its integrity

before reinserting it.

3. 

The filter always has to be installed when the device is being used in order to protect the pump

valves from sand particles and other pollutants.

© by WilTec Wildanger Technik GmbH 

Item 62571

Page 10 

http://www.WilTec.de
http://www.aoyue.eu

 

11 2020

-1

http://www.teichtip.de

Summary of Contents for 62571














Reviews: