WilTec 50752 Operation Manual Download Page 8

  

© by WilTec Wildanger Technik GmbH  

 

Seite 8  

http://www.wiltec.info  

 

 

Disposal regulations 

 
 

 

EU  guidelines  regarding  the  disposal  of  scrap  electric  appliances  (WEEE,  2002/96/EC)  were 
implemented in the law related to electrical and electronic equipment and appliances. 
 
All  Wiltec  electric  devices  that  fall  under  the  WEEE  regulations  are  labelled  with  the  crossed-out 
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the 
domestic waste. 
 
The  company  Wiltec  Technik  GmbH  has  been  registrated  in  the  German  registry  EAR  under  the 
WEEE-registration number 

DE45283704

 

Disposal  of  used  electrical  and  electronic  appliances 
(intended  for  use  in  the  countries  of  the  European 
Union  and  other  European  countries  with  a  separate 
collection system for these appliances). 
The logo on the article or on  its packaging points out 
that  this  article  must  not  be  treated  as  normal 
household  waste but  must  be  disposed  to  a  recycling 
collection  point  for  electronic  and  electrical  waste 
equipment.  By  contributing  to  the  correct  disposal  of 
this article you protect the environment and the health 
of  your  fellow  men.  Environment  and  health  are 
threatened by inappropriate disposal. 
M

aterials’ recycling helps reduce the consumption of raw materials. 

Additional  information  on  recycling  this  article  can  be  provided  by  your  local  community,  municipal 
waste disposal facilities or the store where you purchased the article.

 

 
 
 
 

Address: 

WilTec Wildanger Technik GmbH 

Königsbenden 12 / 28 

D-52249 Eschweiler 

 
 
 
 
 
 
Important notice: 

 
The reprint or reproduction, even of excerpts, and any commercial use, even in part

 

of this instructions 

manual require the written

 

permission

 

of Wiltec Wildanger Technik GmbH. 

Summary of Contents for 50752










Reviews: