background image

4

OPTION 1
 AIR VENT BRACkET 

1.  Insert the two vent clips into the circular hole in the bracket and slide them 

to each end of the slot. The flat surface of the clips should face upward.

2.  Slide the bracket clips into the chosen vent location until they snap into 

place. If necessary, use a thin-bladed screwdriver to gently pry the clips 

apart as they slide into the vent.

3.  Position the moveable arm at the base of the bracket to achieve the 

desired angle and to provide additional stability for the C-Booster™.

OPTION 2
ADHESIVE BRACkET 

1.  Clean the area where the bracket is to be mounted with an alcohol pad 

and a soft cloth. Allow to dry.

2.  Peel the backing to expose the adhesive and press the bracket onto 

the desired location in the vehicle. Note: be sure the tab is positioned 

vertically

, not horizontally.

3.  Allow the adhesive to cure for 24 hours before you attach the C-Booster™.

4.  Once the cradle is attached, you can adjust the angle of the adhesive 

bracket by applying gentle pressure to the top or bottom of the 

C-Booster™. Lock bracket into position with a Phillips head screwdriver 

once desired angle is established.

OptiOn 3

ADHESIVE/SCREW SWIVEL BRACkET 

This mount allows for adhesive mounting as well as more permanent 

screw mounting.  This option is designed to swivel when the knurled nut is 

loosened, for greater adjustability of the C-Booster™ viewing angle.  For 

adhesive mounting, follow steps 1, 2 and 3 of option 2.

For screw mounting

, use an ice pick or an awl to punch through the 

adhesive and expose the four screw holes in the bracket. You must provide 

the screws of an appropriate size for your particular application. Using the 

bracket as a template, mark the locations for the screws as shown, drill pilot 

holes, attach the bracket with adhesive, and tighten all screws.

2.  Attach the Mounting Bracket

Three different mounting brackets are provided for attaching the C-Booster™ to your vehicle’s dash.  Choose the appropriate one for 

your application.  See bracket specific mounting options below.

*Curve is a registered trademark of Research In Motion Limited, Inc.

wpsantennas.com

1-877-594-5766

wpsantennas.com

1-877-594-5766

Summary of Contents for SIGNALBOOST C-Booster









Reviews: