background image

6

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660  

or email: [email protected].    Mon.- Fri. Hours: 7 am to 6 pm MST.

Note:

 Never point the front of a directional antenna toward the Inside  

 

Antenna. See Figures 1 & 2 on page 10.

Finding the Strongest Signal

When installing your Signal Booster’s Outside Antenna, aiming it towards 
the best signal source from you service provider is important.  The best way 
of getting the strongest signal is to have one person on the roof to rotate the 
Outside Antenna, which is connected to the Signal Booster. Turn the Outside 
Antenna about 45 degrees at a time, while the second person is watching the 
signal strength on the phone inside the building. This allows you to read the 
signal strength from the cell tower.  It is preferable to have the phone in the 
test mode so the actual signal strength can be read, as bars are not the most 
accurate. Go to 

www.WilsonElectronics.com

 for help in finding the test mode for 

your phone. Always make sure the person inside the building gives the signal 
time to arrive and register on the phone (between 10-30 seconds for phone to 
reset to the signal reading).

-50dB

-60dB

-70dB

-80dB

-90dB

-100dB

-110dB

EXCELLENT

GOOD

POOR

NO

SIGNAL

Signal Strength Graph

Cell Tower

Cell Signal

Outside

Panel 

Antenna

Signal readings usually appear as a negative number (for example, -86). The 
closer you get to zero the stronger the signal. (See graph below).

Summary of Contents for AG Pro Quint Selectable

















Reviews: