Wilson Electronics 4G LTE 700 Installation Manual Download Page 8

7

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660   

or email: [email protected]. Hours: 7 am to 6 pm MST.

8

Mounting Tips for Running Outside  

Antenna Cable

If you are mounting the Outside Antenna on the roof of your 

building, we have found that it is easiest to run your cable 

underneath the down side of your roof’s flashing . If you have 

satellite TV service installed at your home or office, you may be 

able to follow the same route as the satellite TV cables that are 

already running from outside of your building to the inside . After 

routing the cable, we recommend sealing any areas where the 

cable passes into the building with silicone, cable bushings or 

other waterproof sealant to keep your installation from leaking . 

If you are mounting the Outside Antenna to the outside wall of 

your home or building, the simplest way is to run the cable on 

the outside of the wall and attach it to the exterior of your home 

or office . Then drill a hole through the wall where you want the 

cable to appear on the inside of the building . Before drilling, make 

sure that there are no electrical outlets, sewer or water pipes, or 

electrical wiring in the wall that you are about to drill through as 

this could potentially harm you or damage the building . 

After drilling the required hole, run the cable through and seal 

it with silicone, cable bushings or other waterproof sealant to 

Selecting a Direction for the Outside Antenna

Select a location on the roof of the building to install the Outside 

Antenna . Use a cell phone in test mode to find the strongest signal 

from the cell tower . See below for more information . To get the 

strongest signal possible, it is very important to set up your Outside 

Antenna properly . The Inside and the Outside Antenna must be 

mounted in such a way that they are able to pick up the best possible 

cell signal on the outside of the building and provide the best possible 

signal on the inside of the building . Mount the Outside Antenna as 

high as possible facing the cell tower in an area with the best possible 

signal coverage . 

Note:

 Never point the front of a directional antenna 

toward the Inside Antenna. See Figures 1 & 2 on page 12.

Summary of Contents for 4G LTE 700





















Reviews: