background image

8

WIR TX75 C/D Infrared Transmitter

Control Panel

Figure 6: WIR TX75 C/D PRO master rear view

POWER IN

MIC CHANNEL

SELECTOR

TX75 BUS 

OUT TO 

SLAVE (1)

(OR POE

INPUT)

TX75 BUS

OUT TO 

SLAVE (2)

(OR POE

INPUT)

MIC

IN

CH 1 AUDIO 

LEVEL INDICATOR

(YELLOW)

CH 2 AUDIO 

LEVEL

INDICATOR

(YELLOW)

SLAVE TRANSMIT

POWER INDICATOR

(YELLOW)

SLAVE POWER

INDICATOR

(GREEN)

INDICATOR 

LIGHTS

(ON/OFF)

MIC

ADJUSTMENT

POWER 

INDICATOR

(3.3) TX75 D (3.8)

(2.3) TX75 C (2.8)

TX75 BUS IN FROM

MASTER

SLAVE TRANSMIT

STATUS INDICATOR (YELLOW)

SLAVE POWER 

INDICATOR (GREEN)

INDICATOR LIGHTS

(ON/OFF)

A507

PHOENIX INPUTS

Connecting Power

WARNING: MAINS VOLTAGE MUST NOT FALL BELOW 100 VAC, 0R SYSTEM PERFORMANCE WILL BE 

GREATLY REDUCED. UNIT MAY ENTER RESET MODE UNTIL POWER IS RESTORED.

1.  Plug the power supply output cord into “Power In” on the WIR TX75 C/D PRO.

2.  Attach a line cord to the power supply.

3.  Plug the power supply into the AC outlet. TFP 046: 100-240 VAC IN, 50 / 60 Hz.
This system is designed for class 2, low-voltage wiring. Always follow local electrical codes when using low-voltage wiring.

Power over Ethernet

The WIR TX75 C/D PRO has the ability to use a POE power supply to power itself and one slave.  When using POE, one of the 

slave connections is used for the POE connection, and the other can be used to run one slave.  See the section “Connecting 

Master and Slave Units”.

Green Power

The WIR TX75 C/D PRO is equipped with a sleep/power save feature. If no audio is present on either channel for three minutes, 

the transmitter will automatically go into sleep/power save mode. This mode decreases power consumption by 80 percent. Units 

will automatically start up when audio is activated. This sleep/power save feature can be disabled. Contact Williams Sound for 

instructions.
On power up, the WIR TX75 C/D PRO performs a self-test to detect damage due to shipping, handling, tampering or incorrect 

operation. If any failure is present, green indicator lights will blink. See WIR TX75 C/D PRO Indicators table on page 12 for 

instructions on how to read indicator lights. 

Summary of Contents for WIR TX75 C

















Reviews: