White Outdoor 24AD595C190 Operator'S Manual Download Page 7 | Manualshive

Page: 7 / 20

background image

7

Figure 4

•

Place a wheel on each axle with the valve stem
facing outward.

•

Place a flat washer on each axle and secure with
hex slotted nut.

•

Tighten slotted nut until snug and then back off
approximately 1/3 turn or until one of the slots on
the slotted nut lines up with the hole in the axle.

•

Insert cotter pins through slots in nuts and holes in
axle and secure by bending the ends of the cotter
pins in opposite directions.

•

The wheels should spin freely and there should be
no side to side play.

•

Place hub caps in position on wheels and tap onto
axle with a soft hammer or mallet.

WARNING: Maximum tire pressure under
any circumstance is 30 psi. Equal tire
pressure should be maintained at all
times.

•

If equipped with fenders, proceed to next step.

•

Remove the hex nuts, lock washers, flat washers,
and hex bolts from the side of tank.

•

Determine the proper assembly holes in the
fenders over the tires against the tank.

•

Insert hex bolts through flat washers, holes in
fenders, and tank. Secure fender with lock washers
and hex nuts. Tighten securely.

Attaching The Tongue (See Figure 5)

•

Remove two hex bolts, lock washers, and hex nuts
on the front of the reservoir tank.

•

Place the tongue in position and secure with
hardware just removed.

•

Remove the reservoir tank from the blocks.

Figure 5

Attaching Beam To Reservoir Tank (See Figure 6)

•

For shipping purposes, the pressure hose is
attached to the pump on the engine and to the
control valve on the cylinder.

•

Disconnect the pressure hose from the adapter on
the pump.

•

Stand the wedge, beam, and cylinder assembly
upright with cylinder toward the top.

NOTE: This step might require two people.

•

Remove cotter pin and clevis pin from welded
brackets on beam assembly and move the
reservoir tank assembly in position against the
beam.

•

Insert clevis pin just removed through brackets on
beam and reservoir tank assembly. Secure with
cotter pin by bending the ends of the pin in opposite
directions.

Figure 6

Wheel

Hub Cab

Cotter Pin

Hex Slotted
Nut

Flat
Washer

Fender

Lock
Washer

Hex
Nut

Hex
Bolts

Flat
Washer

Reservoir
Tank

Hex
Nuts

Lock
Washers

Hex
Bolts

Tongue

Reservoir
Tank

Clevis
Pin

Cotter
Pin

Brackets

Reservoir
Tank

«
...
5
6
7
8
9
...
»

Summary of Contents for 24AD595C190





















Reviews:

No comments

Related manuals for 24AD595C190

Brand: Wallenstein Pages: 42

Brand: ATIKA Pages: 88

Brand: Far Tools Pages: 26

Brand: Gardeo Pages: 63

Brand: Gardeo Pages: 86

Brand: Ryobi Pages: 42

Brand: power King Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands