White Outdoor 24AD595C190 Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

14

Figure 17

Tires

See sidewall of tire for recommended pressure.
Maximum tire pressure under any circumstances is 30
p.s.i. Equal tire pressure should be maintained on all
tires.

WARNING: Excessive pressure (over 30
p.s.i.) when seating beads may cause tire/
rim assembly to burst with force sufficient
to cause serious injury.

Storing Your Log Splitter

•

Clean the unit thoroughly.

•

Wipe equipment with an oiled rag to prevent rust.

•

Refer to engine manual for correct engine storage
instructions

•

Store unit in a clean, dry area. Do not store next to
corrosive materials such as fertilizer.

WARNING: Never store the machine or
fuel container indoors where there is an
open flame, spark, or pilot light such as on
water heater, furnace, clothes dryer, or
other gas appliance.

WARNING: Drain fuel into an approved
container outdoors, away from an open
flame. Allow engine to cool. Extinguish
cigarettes, cigars, pipes, and other
sources of ignition prior to draining fuel.
Fuel left in engine for extended periods
deteriorates and will cause starting
problems.

ENGINE

PUMP

Set
Screw

Nylon

“Spider”

Insert

Clearance

Steel
Coupling
Halves

«
...
12
13
14
15
16
...
»

Summary of Contents for 24AD595C190





















Reviews:

No comments

Related manuals for 24AD595C190

Brand: Wel-Bilt Pages: 4

Brand: Craftsman Pages: 28

Brand: YTL Pages: 24

Brand: Far Tools Pages: 25

Brand: Racing Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands