White Outdoor 24AD595C190 Operator'S Manual Download Page 1 | Manualshive

Page: 1 / 20

background image

Log Splitter

33-Ton

Model Number

24AD595C190

OPERATOR’S MANUAL

PRINTED IN U.S.A.

FORM NO.

770-10041D.fm

(7/01)

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.

1
2
3
...
»

Summary of Contents for 24AD595C190





















Reviews:

No comments

Related manuals for 24AD595C190

Brand: Scheppach Pages: 38

Brand: Far Tools Pages: 44

Brand: Wallenstein Pages: 12

Brand: Powerhouse Pages: 16

Brand: Blue Max Pages: 15

Brand: Altrad Pages: 20

Brand: Altrad Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands