White Mountain Hearth DVP36FP3 Series Installation Instructions And Owner'S Manual Download

Page: 63 / 68

23340-2-1007

Page 63

CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE

WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION,

MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE

ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES,

WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION).

1. Using gloves, unpack liner components and check for damaged

or missing components.

2. Lower bottom louver and remove upper louver on ﬁreplace.

3. Remove glass frame assembly from ﬁreplace.

4. Remove rear logs from burner assembly.

5. Place brick panel (rear) against rear wall in ﬁreplace.

Note

: The top edge will have a half-moon cutout relief to match

up with the rear ﬂue vent hole.

6. While holding ﬁnished edge on brick panel (side), place brick

panel (sides) against side walls in ﬁreplace. Move side panels

rearward until the back edge meets the rear brick panel. Slide

side brick panels down so they rest on ﬁrebox bottom.

7. Align grout lines on top brick panel with the grout lines on the

side brick panels. Place the top brick panel into brick panel

holder. With needle-nose pliers, carefully bend hold-down tabs

on brick panel holder over the edges of the top brick panel.

The hold-down tabs will securely hold the top brick panel in

place.

8. Replace rear logs onto burner assembly. (Refer to log

placement, page 40.)

9. Attach glass frame assembly onto ﬁreplace.

10. Raise bottom louver and replace top louver onto ﬁreplace.

11. Installation of optional brick liner is complete.

*Note: For intermittent pilot models, refer to wiring instructions on page 46.

A factory installed junction box is located on the lower right

side of the ﬁreplace. Wiring must be fed to the junction box and

attached to the receptacle that is provided. Leave approximately

6" of wire in the junction box for connection.
Attach black wire to one side of the receptacle and white wire to

opposite side of receptacle. The ground wire should be attached to

the green (ground) screw.
Install the receptacle into the junction box. Attach cover plate.
Attention: A Junction box is located on the lower left

side of the ﬁreplace for direct ignition connections on direct ignition

ﬁreplace models only.

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

OPTIONAL BRICK LINER INSTALLATION INSTRUCTIONS

Summary of Contents for DVP36FP3 Series





































































Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands

White Mountain Hearth DVP36FP3 Series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands