White Mountain Hearth DVP36FP3 Series Page 13 Installation Instructions And Owner'S Manual Download

Page: 13 / 68

23340-2-1007

Page 13

Flush Wall Installation

Figure 13

Combustible Surround Installation

Figure 14

Attention: Cold climate installation recommendation: When

installing this unit against a non-insulated exterior wall, it is

recommended that the outer walls be insulated to conform

to applicable insulation codes.

Vent Runs (Figures 15, 16, 17, 18, and 19)

In planning the installation for the ﬁreplace, it is necessary to

install certain components before the appliance is completely

positioned and installed. These include the direct vent system,

gas piping for the appliance and the electrical wiring. (If the fan

option is used.)
The appliance can be mounted on any of the following surfaces:

1. A ﬂat, hard combustible (burnable) surface.

2. A raised wooden platform.

3. Four (4) corner supports. (Example: Four (4) concrete masonry

blocks.) These supports must be positioned so they contact all

four (4) perimeter edges on the bottom of the unit.

VERTICAL, 90° ELBOW WITH HORIZONTAL

TERMINATION

Figure 15

3! OF NON-COMBUSTIBLE MATERIAL

FINISHED WALL

FRONT TRIM OR NON-

COMBUSTIBLE MA TERIAL

(INSTALLA TION IS OPTIONAL)

JOINT BETWEEN FINISHED

WALL AND UNIT SEALED

WITH 300° F, 149° C SEALANT

MATERIAL

(Sealant is optional)

DVP36

49 ½

”

(126 mm)

TO BOTTOM

OF UNIT

VENT CAP/

THIMBLE

THIMBLE

3! OF NON-COMBUSTIBLE MATERIAL

FINISHED WALL

FRONT TRIM OR NON-COMBUSTIBLE

MATERIAL (INSTALLATION IS OPTIONAL)

JOINT BETWEEN FINISHED WALL AND

UNIT SEALED WITH 300° F 149

MATERIAL (SEALANT IS OPTIONAL)

° C

SEALANT

COMBUSTIBLE SURROUND

MANTELSHELF

2 X 4

HEADER

STAND OFF

LP and Nat models

Summary of Contents for DVP36FP3 Series





































































Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands

White Mountain Hearth DVP36FP3 Series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands