White Mountain Hearth DVP36FP3 Series Installation Instructions And Owner'S Manual Download

Page: 19 / 68

23340-2-1007

Page 19

PRE-INSTALLATION INFORMATION:

Items Required For Installation:

Tools

Building Supplies

Phillips Screwdriver

Hammer

Saw and/or saber saw

Level

Measuring Tape

Electric Drill and Bits

Pliers

Square

Tin Snips

Framing Materials

Wall Finishing Materials

Caulking Material (Noncombustible)

Support Strap supplies

Before You Start:

Plan your installation. Read these instructions and the ﬁreplace installation manual before installing unit and vent system. Set unit in

place and survey how best to vent the unit. After the vent conﬁguration has been decided, stretch the ﬂex pipe components out, then trim

off what will not be needed.

Refer to the ﬁreplace installation manual for information on vertical venting requirements. The maximum length of vent when using ﬂex

venting is 35 feet total. Contact your dealer or distributor for information on ﬂex vent extension kits that may be added to the DVVK-

4FV kit, in order to terminate up to 35 feet. Available extension kits include the DVEK-10 (10’ Flex) or the DVEK-25 (25’ Flex) exten-

sion kits. The extension kits include connection hardware.

Installation of the Vertical Flex Termination Kit

WARNING

Ensure that the venting system exits the structure through the roof and does not terminate less than 12 inches (305mm) above the

roof.

WARNING

Refer to your ﬁreplace homeowner’s manual for the minimum and maximum venting requirement of your ﬁreplace prior to installa-

tion. Failure to do so may cause a ﬁre hazard.

WARNING

This ﬂexible pipe termination kit is ONLY for vertical terminations.

WARNING

Any horizontal run section must have a 1/4” rise for every one (1) foot of run towards the vent termination. Never allow the vent pipe

to run downward. This could cause high temperatures and may present a ﬁre hazard. This vertical kit may incorporate two (2) 90 de-

gree bends, but must terminate vertically.

CAUTION

This ﬂex vent kit can be installed either vertically or horizontally off of Direct Vent Series ﬁreplaces but must only terminate verti-

cally.

WARNING

Because of sharp edges, always use gloves when handling the ﬂex vent components.

CAUTION

Vent connections should overlap a minimum of 1” for proper sealing.

CAUTION

Always stretch and secure venting with metal strapping secured with nails (nails and strapping not supplied) to ensure that the ﬂex

vent runs remain true.

INSTALLATION NOTE:

If space permits, it is generally easier to attach venting in the top vent conﬁguration.

Summary of Contents for DVP36FP3 Series





































































Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands

White Mountain Hearth DVP36FP3 Series, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for DVP36FP3 Series

Reviews:

Related manuals for DVP36FP3 Series

Brands by name

Popular brands