background image

9

Door Reversal—Side Swing Only

Tools Needed

Gather the required tools and parts before starting installation.

 

5/16" wrench

 

1/4" wrench

 

Flat putty knife

 

Phillips screwdriver

Remove Stainless Steel Door Wrap Panel  

(on some models)

1. 

Remove the two hex-head screws located under the stainless 

steel door wrap panel flange on the bottom of the door.

2. 

Pull up and outward on the door wrap panel from the bottom.

3. 

Rotate the door wrap panel until it separates from the door 

and pull up.

NOTE:

 Be sure the edge guards do not separate from the 

door wrap panel.

Door Stop and End-Cap Reversal

1. 

Unplug the ice maker or disconnect power.

2. 

Remove the handle screws and handle (on some models).

3. 

Remove the hinge pin from the top hinge.

4. 

Remove the door from the hinges and replace the top hinge 

pin.

5. 

Remove the screw and door stop at corner A. Remove the 

screw and end cap at corner C. Place the door stop at corner 

C, and tighten screw. Place the end cap at corner A, and 

tighten screw.

6. 

Remove the screw and door stop at corner D. Remove the 

screw and end cap at corner B. Place the door stop at corner 

B, and tighten screw. Place the end cap at corner D, and 

tighten screw.

7. 

Depending on your model, the brand badge for the front door 

of your ice maker may be in the package with the Use and 

Care Guide. Fasten the brand badge to the door.

8. 

Set the door aside.

Hinge pin

A

A. Hex-head screws

WARNING

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

A

B

D

C

A. Top corner open (no end cap)
B. Beginning top corner end cap

C. Beginning bottom corner end cap
D. Bottom corner open (no end cap)

5/16" hex-head hinge screw

Handle screw

End cap screw

Summary of Contents for WUI75X15













Reviews: