background image

6

2. 

Unplug ice maker or disconnect power.

3. 

Turn off water supply. Wait 5 to 10 minutes for the ice to fall 

into the storage bin. Remove all ice from bin.

4. 

Unscrew the drain cap from the bottom of the water 

pan located inside the storage bin. Allow water to drain 

completely. Replace drain cap. See “Drain Cap” illustration.

Drain Cap

5. 

If ice maker is built into cabinets, pull ice maker out of the 

opening.

6. 

Disconnect water supply line. See “Water Supply Line” 

illustration.

Water Supply Line

Drain Pump Installation

NOTE:

 Do not kink, smash or damage tubes or wires during 

installation.

1. 

Unplug ice maker or disconnect power.

2. 

Remove rear panel. See “Rear Panel” illustration for 5 screw 

locations. Pull rear panel away from the drain tube and 

discard.

Rear Panel

3. 

Remove the old drain tube and clamp attached to the ice 

maker bin.

NOTE:

 Discard old drain tube and clamp.

4. 

Install new drain tube (5/8" I.D. x 5¹⁄

8

") from ice maker bin to 

drain pump reservoir inlet using new adjustable clamps. See 

“Drain Tube” illustration.

NOTES:

 

Do not kink.

 

Trim tube length if required.

Drain Tube

5. 

Install vent tube (5/16" I.D. x 32" [81 cm]) to drain pump 

reservoir vent. Use one of the supplied 5/8" small adjustable 

clamp. See “Parts Locations” illustration.

NOTE:

 Do not install household drain tube at this time.

Parts Locations

6. 

Remove power cord clamp and ground screw attached to ice 

maker power cord, which is mounted to the unit base. See 

“Parts Locations” illustration.

NOTE:

 Clamp and screw will be reused.

A

A. Drain cap

B

C
D

E

A

C

B

A. 1/4" (6.35 mm)

 

copper 

tubing

B. Cable clamp
C. 1/4" compression nut

D. Ferrule (sleeve)
E. Ice maker connection

A

A

A. Screw locations

A

B

C

D

A. 7/8" adjustable hose clamp
B. Drain tube (ice bin to drain pump)

C. 7/8" adjustable hose clamp
D. Drain pump reservoir inlet

A

B

D

E

C

G

F

A. Vent tube
B. 5/8" hose clamp
C. Drain pump discharge tube
D. Drain pump

E. Ice maker unit power cord
F. #8-32 x 3/8" pump mounting 

screws

G. Drain pump power cord, clamp 

and screw

Summary of Contents for WUI75X15













Reviews: