Whirlpool WGHP43 Installation Instructions Manual Download Page 11

Page: 11 / 16

TROUBLESHOOTING INFORMATION

Problem

No Cooling/Heating

Cause/Test Method and/or Solution

■

System will not start.

■

Power failure. Test voltage.

■

Blown fuse. Inspect fuse size and type. Replace, if needed.

■

Loose connection. Inspect connection. Tighten if needed.

■

Shorted or broken wires. Test circuits with ohmmeter. Replace if needed.

■

Faulty thermostat. Test continuity of thermostat and wiring. Replace, if needed.

■

Faulty transformer. Check control circuit with voltmeter. Replace, if needed.

■

Compressor will not start—fan runs.

■

Shorted or broken wires. Test circuits with ohmmeter. Replace if needed.

■

Shorted or open capacitor. Test capacitor.

■

Internal compressor overload open. Test continuity of overload.

■

Shorted or grounded compressor. Test motor windings.

■

Compressor stuck. Use test cord.

■

Low voltage. Test voltage.

■

Compressor and condenser fan will
not start.

■

Blown fuse. Inspect fuse size and type. Replace, if needed.

■

Shorted or broken wires. Test circuits with ohmmeter. Replace if needed.

■

Faulty thermostat. Test continuity of thermostat and wiring. Replace, if needed.

■

Faulty transformer. Check control circuit with voltmeter. Replace, if needed.

■

Faulty compressor contactor. Test continuity of coil and contacts. Replace, if needed.

■

Evaporator fan will not start.

■

Blown fuse. Inspect fuse size and type. Replace, if needed.

■

Loose connection. Inspect connection. Tighten if needed.

■

Shorted or broken wires. Test circuits with ohmmeter. Replace if needed.

■

Open fan overload. Test continuity of overloads.

■

Faulty thermostat. Test continuity of thermostat and wiring. Replace, if needed.

■

Shorted or open capacitor. Test capacitor.

■

Faulty fan relay. Test continuity of coil and contacts.

■

Open control circuit. Test control circuit with voltmeter.

■

Faulty evaporator fan motor. Repair or replace.

■

Condenser fan will not start.

■

Shorted or broken wires. Test circuits with ohmmeter. Replace if needed.

■

Open fan overload. Test continuity of overloads.

■

Shorted or open capacitor. Test capacitor.

■

Faulty compressor contactor. Test continuity of coil and contacts. Replace, if needed.

■

Shorted or grounded fan motor. Test motor windings.

■

Faulty defrost control. Test control.

Summary of Contents for WGHP43

















Search results

Summary of Contents for WGHP43

Reviews:

Related manuals for WGHP43

Brands by name

Popular brands

Whirlpool WGHP43, Installation Instructions Manual

Search results

Summary of Contents for WGHP43

Reviews:

Related manuals for WGHP43

Brands by name

Popular brands