background image

3

GAS FURNACE SAFETY PRECAUTIONS

Please adhere to the following warnings and cautions when installing, adjusting, altering, servicing or operating the furnace. To ensure 
proper installation and operation, thoroughly read this manual for specifics pertaining to the installation and application of this product.

Recognize this symbol as a safety precaution.

Hazards or unsafe practices could result in property
damage, product damage, severe personal injury or death. 

Hazards or unsafe practices may result in property
damage, product damage, personal injury or death. 

WARNING

CAUTION

The manufacturer will not be responsible for any injury
or property damage arising from improper service or
service procedures. If you install or perform service on
this unit, you assume responsibility for any personal 
injury or property damage which may result. Many
jurisdictions require a license to install or service 
heating and air conditioning equipment.

WARNING

To prevent personal injury or death due to improper
installation, adjustment, alteration, service  or  maintenance,
refer to this manual. For additional assistance or
information, consult a qualified installer, service agency
or the gas supplier.

WARNING

If the information in these instructions is not followed
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.

— Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone 

in your building.

• Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire 

department.

— Installation and service must be performed by a 

qualified installer, service agency or the gas supplier.

WARNING

This product contains or produces a chemical or 
chemicals which may cause serious illness or death and
which are known to the State of California to cause 
cancer, birth defects or other reproductive harm.

WARNING

Heating unit should not be utilized without reasonable,
routine inspection, maintenance and supervision. If the
building in which any such device is located will be 
vacant, care should be taken that such device is
routinely inspected, maintained and monitored. In the
event that the building may be exposed to freezing 
temperatures and will be vacant, all water-bearing pipes 
should be drained, the building should be properly 
winterized and the water source closed. In the event
that the building may be exposed to freezing
temperatures and will be vacant, any hydronic coil units
should be drained as well, and, in such case, alternative
heat sources should be utilized.

WARNING

CARBON MONOXIDE POISONING HAZARD

Special Warning for Installation of Furnace or Air Handling 
Units in Enclosed Areas such as Garages, Utility Rooms or 
Parking Areas. 

Carbon monoxide producing devices (such as an 
automobile, space heater, gas water heater, etc.) should 
not be operated in enclosed areas such as unventilated 
garages, utility rooms or parking areas because of the 
danger of carbon monoxide (CO) poisoning resulting from 
the exhaust emissions. If a furnace or air handler is 
installed in an enclosed area such as a garage, utility room 
or parking area and a carbon monoxide producing device is 
operated therein, there must be adequate, direct outside
ventilation.
This ventilation is necessary to avoid the danger of CO 
poisoning which can occur if a carbon monoxide producing 
device continues to operate in the enclosed area. Carbon 
monoxide emissions can be (re)circulated throughout the 
structure if the furnace or air handler is operating in any
mode.

CO can cause serious illness including permanent brain 
damage or death.

DANGER

Summary of Contents for WGFD28









































Reviews: