background image

12

Remove/Replace Drawer

Remove all items from inside the storage drawer, and then  

allow the range to cool completely before attempting to  

remove the drawer.

To Remove:

1. 

Open the drawer to its fully open position.

2. 

Raise the front edge and then lift out.

To Replace:

1. 

Align the forward drawer notches with the notches in the 

drawer rails on both sides. Place the rear alignment tabs into 

the drawer rails on both sides.

2. 

Push the drawer in all the way.

3. 

Gently open and close the drawer to ensure it is seated 

properly on the rails on both sides.

Oven Door

For normal range use, it is not suggested to remove the oven 

door. However, if removal is necessary, make sure the oven is OFF 

and cool. Then, follow these instructions. The oven door is heavy.

To Remove:

1. 

Open oven door all the way.

2. 

Pinch the hinge latch between two fingers and pull forward. 

Repeat on other side of oven door.

3. 

Close the oven door as far as it will shut.

4. 

Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away  

from the oven doorframe.

A

A.  Hinge latch

To Replace:

1. 

Insert both hanger arms into the door. Be sure that the  

hinge notches are engaged in the oven doorframe.

2. 

Open the oven door.
The door should be able to open all the way.

3. 

Move the hinge levers back to the “locked” position.  

Check that the door is free to open and close and is level 

while closed. If it is not, repeat the removal and installation 

procedures.

Complete Installation

1. 

Check that all parts are now installed. If there is an extra part, 

go back through the steps to see which step was skipped.

2. 

Check that you have all of your tools.

3. 

Check that you have all of the range accessories, especially 

oven racks. These accessories may be in the range 

packaging.

4. 

Dispose of/recycle all packaging materials.

5. 

Check that the range is level. See the “Level Range” section.

6. 

Use a mild solution of liquid household cleaner and warm 

water to remove waxy residue caused by shipping material. 

Dry thoroughly with a soft cloth. For more information, see 

the “Range Care” section of the User Guide.

7. 

Read the User Guide.

8. 

Turn on surface burners and oven. See the User Guide  

for specific instructions on range operation.

NOTE:

 Odors and smoke are normal when the oven is used 

the first few times.

If Range Does Not Operate, Check the Following:

 

Household fuse is intact and tight, or circuit breaker has  

not tripped.

 

Gas pressure regulator shut-off valve is in the “open” position.

 

Range is plugged into a grounded 3 prong outlet.

 

Electrical supply is connected.

9. 

When the range has been ON for 5 minutes, check for heat. 

If the range is cold, turn off the range and check that the gas 

supply line shut-off valve is open.

 

If the gas supply line shut-off valve is closed, open it,  

and then repeat the 5-minute test as outlined above.

 

If the gas supply line shut-off valve is open, close it,  

and contact a qualified technician.

If You Need Assistance or Service:

Please reference the “Warranty” section of the User Guide  

to contact service.

A

A.  Hinge notch

Summary of Contents for WEG515S0FV0





















Reviews: