Whirlpool WED9250WH Installation Instructions Manual Download Page 8

Page: 8 / 16

Remove center, silver-colored terminal block screw. Remove

neutral ground wire from external ground conductor screw.

Prepare to connect neutral

ground wire and neutral wire.

Choose a standard power supply cord connector:

4-wIre pOwer SUppLy COrD

CONNeCTION

Flanged spade connectors Ring connectors

Connect neutral ground wire

and neutral wire

Connect neutral ground wire and neutral wire (white or center

wire) of power supply cord under center, silver-colored

terminal block screw. Tighten screw.

Connect ground wire (green or bare) of power supply cord

to external ground conductor screw. Tighten screw.

Connect ground wire

Connect remaining wires to outer terminal block screws.

Tighten screws. Finally, reinsert tab of terminal block cover into

slot of dryer rear panel. Secure cover with hold-down screw.

Now, go to Venting Requirements.

Connect remaining wires

10.

Choose a standard power supply cord connector:

3-wIre pOwer SUppLy COrD

CONNeCTION

Flanged spade connectors Ring connectors

Remove center, silver-colored terminal block screw.

11.

Remove center screw

12.

Connect neutral wire

Connect neutral wire (white or center wire) of power supply cord

to center, silver-colored screw on terminal block. Tighten screw.

Summary of Contents for WED9250WH
















Search results

Summary of Contents for WED9250WH

Reviews:

Brands by name

Popular brands

Whirlpool WED9250WH, Installation Instructions Manual

Search results

Summary of Contents for WED9250WH

Reviews:

Brands by name

Popular brands