Whirlpool W10441071B, Use & Care Manual

Page: 13 / 48

13
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm or hot water washes sometimes (not exclusively
cold water washes), because they do a better job of
controlling the rate at which soils and detergent accumulate.
3. Always leave the washer door slightly ajar between uses
to help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Front Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Door Seal
1.
Open the washer door and remove any clothing or items
from the washer.
2. Inspect the colored seal between the door opening and
the drum for stained areas or soil buildup. Pull back the
seal to inspect all areas under the seal and to check for
foreign objects.
3. If stained areas or soil buildup are found, wipe down
these areas of the seal using either of the following
two procedures:
a. affresh
®
Grit Grabber™ Cloth Procedure:
i. When the cycle is complete, gently pull back the
rubber door seal and clean the entire surface with
the rough side of the Grit Grabber™ cloth.
b. Dilute Liquid Chlorine Bleach Procedure:
i. Mix a dilute bleach solution, using 3/4 cup (177 mL)
of liquid chlorine bleach and 1 gallon (3.8 L) of warm
tap water.
ii. Wipe the seal area with the dilute solution, using
a damp cloth.
iii. Let stand 5 minutes.
iv. Wipe down area thoroughly with a dry cloth and let
washer interior air dry with door open.
IMPORTANT:
n
Wear rubber gloves when cleaning with bleach.
n
Refer to the bleach manufacturer’s instructions
for proper use.
WASHER CARE (cont.)
Cleaning the Inside of the Washer
This washer has a special cycle that uses higher water
volumes in combination with affresh
®
Washer Cleaner or
liquid chlorine bleach to thoroughly clean the inside of the
washer. Steam washer models also utilize steam to enhance
cleaning in this special cycle.
NOTE:
Read these instructions completely before beginning
the cleaning process.
Begin procedure
1. affresh
®
Washer Cleaner Cycle Procedure
(Recommended for Best Performance):
a.
Open the washer door and remove any clothing
or items.
b.
Add an affresh
®
Washer Cleaner tablet to the washer
drum.
c.
Do not add the affresh
®
Washer Cleaner tablet
to the dispenser drawer.
d.
Do not add any detergent or other chemical to the
washer when following this procedure.
e.
Close the washer door.
f.
Select the CLEAN WASHER cycle.
g.
Touch and hold START to begin the cycle. The Clean
Washer Cycle Operation is described below.
2. Chlorine Bleach Procedure:
a.
Open the washer door and remove any clothing
or items.
b.
Open the dispenser drawer and add liquid chlorine
bleach to the MAX level in both the bleach
compartment and the fabric softener compartment.
NOTE:
Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c.
Close the washer door and the dispenser drawer.
d.
Do not add any detergent or other chemicals to the
washer when following this procedure.
e.
Close the washer door.
f.
Select the CLEAN WASHER cycle.
g.
Touch and hold START to begin the cycle. The Clean
Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle.
Description of Clean Washer Cycle Operation:
1.
The Clean Washer cycle will determine whether clothing
or other items are in the washer.
2.
If no items are detected in the washer, it will proceed
with the cycle.
a.
If any items are detected in the washer, “rL” (remove
load) will be displayed. The door will unlock. Open
washer and remove any garments from the washer
drum.
b.
Touch POWER to clear the “rL” code.
c.
Touch and hold START to restart the cycle.
After the cycle is complete, leave the door open slightly to
allow for better ventilation and drying of the washer interior.
WASHER MAINTENANCE
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
WATER INLET HOSES