Whirlpool JOB AID GC1SHAXM Installation And Operation Manual Download Page 55

Page: 55 / 56

PRODUCT SPECIFICATIONS

AND

WARRANTY INFORMATION SOURCES

IN THE UNITED STATES:

FOR PRODUCT SPECIFICATIONS AND WARANTY INFORMATION CALL:

FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL:

THE TECHNICAL ASSISTANCE LINE: 1-800-253-2870

HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN

AUTHORIZED SERVICER

IN CANADA:

FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL:

1-800-461-5681

FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL:

THE TECHNICAL ASSISTANCE LINE: 1-800-488-4791

HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN

AUTHORIZED SERVICER

FOR WHIRLPOOL PRODUCTS: 1-800-253-1301
FOR KITCHENAID PRODUCTS: 1-800-422-1230
FOR ROPER PRODUCTS: 1-800-447-6737

FOR LITERATURE ORDERS:

PHONE: 1-800-851-4605

FOR TECHNICAL INFORMATION AND SERVICE POINTERS:

www.servicematters.com

Summary of Contents for JOB AID GC1SHAXM

























































Search results

Summary of Contents for JOB AID GC1SHAXM

Reviews:

Related manuals for JOB AID GC1SHAXM

Brands by name

Popular brands

Whirlpool JOB AID GC1SHAXM, Installation And Operation Manual

Search results

Summary of Contents for JOB AID GC1SHAXM

Reviews:

Related manuals for JOB AID GC1SHAXM

Brands by name

Popular brands