manualshive.com logo in svg

Whirlpool CATALYST, Troubleshooting & Repair Manual, Page: 22 / 44

Share
Download
Whirlpool CATALYST Troubleshooting & Repair Manual Download Page 22

18

CABINET

Fig. 7

4. Rotate the access cover on the washer top clockwise to expose the hose assemblies under-

neath. 

(Fig. 6)

5. Disconnect the bleach dispenser venturi hoses and the detergent and fabric softener inlet

hoses as indicated in 

Figure 6

.

6. Pull the inner basket forward, to avoid damage to the tub ring, splash guard and shield.  Re-

move

the cabinet by tilting it forward and pulling it away from the washer.  

(Fig. 7)

BLEACH DISPENSER

VENTURI HOSE

DETERGENT

DISPENSER

INLET HOSE

FABRIC SOFTENER

DISPENSER

OUTLET HOSE

Fig. 6

BLEACH DISPENSER

VENTURI HOSES

VENTURI

ACCESSING COMPONENTS IN THE WASHER CABINET

Components inside the washer cabinet can be accessed by completely removing
the outer cabinet as one unit.  Refer to 

Figure 5

 for the following instructions.

1. Remove the console mounting screws and

tilt the console into the service position.

2. Unplug the lid switch harness connector

from the receptacle in the washer top.

3. Remove the cabinet mounting clips

by placing the flat blade of a screwdriver
in the clip as shown in 

Figure 5, Inset 1

.

INSET 1

CLIP

CLIP

Fig. 5

Summary of Contents for CATALYST













































Reviews:

No comments