background image

 

273 Branchport Avenue 
Long Branch, N.J.  07740 
(732)  222-6880 

 
 

INSTALLATION INSTRUCTIONS 

ZONE CONTROL MODULE (3 ZONES) 

MODEL NUMBER ZC-3 

 
 

FCC REGULATIONS 
 
This equipment complies with Part 68 of the FCC Rules.  On the back of this equipment is a label that contains, among other information, the FCC 
Registration Number and the Ringer Equivalence Number (REN) for this equipment.  You must, upon request provide this information to your telephone 
company. 
 
The REN is also useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices ring when your 
telephone number is called.  In most, but not all areas, the sum of the REN's of all devices connected to one line should not exceed five (5.0).  To be 
certain of the number of devices that you may connect to your line, you may want to contact your local telephone company. 
 
Should the equipment cause harm to the telephone network, the telephone company shall, if possible, notify the customer that temporary discontinuance 
of service may be required.  However, where prior written notice is not possible, the telephone company may temporarily discontinue service without 
notice, if such action is necessary under the circumstances.  The telephone company may make changes in its communication facilities, equipment and 
operations procedures, where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations of 
the Federal Communications Commission. 
 
Do not attempt to repair or modify this equipment.  Repairs to this product will be performed by Wheelock Inc. 273 Branchport Ave, Long Branch, NJ  
07740 in accordance with Wheelock Inc.'s published Terms and conditions of Sale.  This equipment should not be used on coin telephone lines.  
Connection to party line service is subject to state tariffs. 
 
If trouble is experienced, disconnect this equipment from the telephone line to determine if it is causing the malfunction.  If the equipment is determined 
to be malfunctioning, its use shall be discontinued until the problem has been corrected. 
 
 
APPLICATION INFORMATION 
 

  WARNING: 

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER DOCUMENTS 
DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE, 
INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT 
THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY FOR SUCH USE. 

 
 
The ZC-3 Zone Control Module provides the central control, switching and signaling required to perform the following functions when connected to an 
unused loop start CO port of electronic (EKSU), mechanical (1A2) key PBX telephone systems.  It can also be connected to a 600 OHM low power audio 
page port which transmits DTMF touchtones and provides a contact closure. 
 
 
1. 

Three zones of paging (one-way and/or Talkback) 

2. All-Call 
3. 

Background music input to any or all zones 

4. 

Background music mute: 

 

A.  Per Zone - only within the paged zone 

 

B.  Total system - on All-Call 

5. 

Alert tone prior to page: 

 

A.  Per zone - only within the paged zone 

 

B.  Total system - on All-Call 

6. 

Alert tone volume adjustment (with "OFF" position) 

7. 

Talkback Inhibit on All-Call 

8. 

Provides talk battery to an unused CO line/trunk port. 

 
The Zone Control Module can be used with: 
 
1. Speaker 

Amplifiers 

2. 

Wheelock TBM-101 Talkback Speaker Module and TBH-104 Talkback Horn System. 

 

Modules - maximum of one per zone 

3. 

Zone Amplifiers (one per zone) for 25V/70V paging systems. 

4. 

Any combination of items (1) thru (3) (Not mixed in the same zone). 

 
Copyright 1987, 1988, 1989, 1991, 1992, 1993 Wheelock Inc.  All rights reserved. 

P81414 K 

Sheet 1 of 6 

A maximum of 10 Speaker Amplifiers (including TBM-101 and TBH-104 Talkback Modules) can be connected to one Zone Control Module, based upon 
a minimum audio input signal of -15dBM (0.1VRMS) at each speaker-amplifier.  Depending upon the paging systems configuration, and the available 
audio output signal from the host telephone system, the audio input signal may be less.  If additional volume is required, use Wheelock's PRM-150 

Summary of Contents for ZC-3







Reviews: