background image

westinghouse.com.au

CONGRATULATIONS

Congratulations and thank you for choosing our 

integration kit. Before you install the integration kit, 

we recommend that you read through the entire 

installation manual.

To avoid the risks that are always present when you 

install an electrical appliance, it is important that the 

integration kit and appliance are installed correctly. 
Please read the safety instructions in this installation

 

manual as well as the appliance’s user manual to 

carefully to avoid misuse and hazards.

We recommend that you keep this instruction booklet  

for future reference and pass it on to any future owners.

 

After unpacking the integration kit, please check it is 
not damaged. If in doubt, do not use the integration kit

 

but  contact your local Westinghouse Customer Care 

Centre.

BEFORE YOU CALL 

Please ensure you read the instruction manual fully 
before you call for service, or a full service fee could be 
applicable.

INFORMATION ON DISPOSAL 

FOR USERS

  ENVIRONMENT! 

 

Most of the packaging materials are recyclable.
Please dispose of these materials through your
local recycling depot or by placing them in
appropriate collection containers.

 

If you wish to discard this product, please
contact your local authorities and ask for the
correct method of disposal.

CONTENTS

General warnings  .......................................................... 2 
Refrigerator integration kit items

  ............................

Cupboard dimensions ..................................................

Installation of 120˚ hinge  ............................................ 7 
Preparation ....................................................................... 7 
Attaching the rear rollers  ............................................ 8 
Attaching top hinge bracket  ..................................... 9 
Attaching slide-housing to refrigerator door.....   9 
Placing refrigerator in cupboard .............................. 11 
Refrigerator alignment  ................................................ 12 
Securing refrigerator in cupboard ........................... 13 
Attaching slide-bar to cupboard door .................... 13 
Notes ......................................................................

15

GENERAL WARNINGS 

 

Please read the user manual carefully and store in 

a handy place for later reference. Pass the user 

manual on to possible new owners of the appliance.

NOTE: We strongly recommend that a professional 
builder/cabinet maker builds this unit into required 

cabinetry prior to finished installation in customer’s 

kitchen. Westinghouse cannot take responsibility 

for any installation issues when customer retrofits 

this product into cabinetry. Cabinet door height built 
in excess of refrigerator door height will be 
unsupported and risk bowing.

NOTE: Please refer to your Appliance User Manual for 

warnings relating to the appliance.

SYMBOLS

  WARNING!

This symbol indicates information concerning your  
personal safety

  CAUTION!

This symbol indicates information on how to avoid 
damaging the refrigerator

  IMPORTANT!

This symbol indicates tips and information about 
use of the refrigerator

  ENVIRONMENT!

This symbol indicates tips and information about 
economical and ecological use of the refrigerator 

Curved Door Fridge

Flat Door Fridge

Summary of Contents for WBE4504

















Reviews: