6
7
INSTALLING
ACCESSORIES
INSTALLATION
preparing your appliance for the
first time
• Please remove all internal boxes and bags from the oven
before operation�
• Please wipe out the oven interior prior to operation with
warm soapy water and polish dry with a soft clean cloth�
Do not close the oven door until the oven is completely
dry�
• New appliances can have an odour during first
operation. It is recommended to ‘run in’ your oven before
you cook for the first time� Run the oven at 180ºC for 2-4
hours and ensure that the room is well ventilated�
• DO NOT line the oven with foil, it will damage the enamel.
• If your appliance is fitted with a 2-hour “Auto Off”
timer, make sure it is set to the ‘Off’ marker for manual
operation� See image�
Setting the time (POR788 only)
After electrically connecting the appliance, you must set the
time of day before you can operate your oven�
1� After the appliance has been electrically connected
“12:00” will flash on the clock display, along with the
scrolling message “Welcome to Electrolux”�
2� To set the time of day in hours and minutes, press the
or buttons underneath the “set clock” graphic�
3. 8 seconds after the last change the time will stop flashing,
confirming the time has been set� Once the time has been
entered, the clock advances minute
by minute�
Note:
• The clock has a 12 hour display
• The display has 3 levels of brightness.
– Brightest illumination: whenever the oven is in use.
– Medium illumination: the oven is not in use.
– Lowest illumination: the oven is not in use between
the hours of 10pm and 6am.
side racks
The side racks that come with your oven are all fitted the
same way and can be attached to either side of your oven�
• Insert the largest peg into rear access hole provided. See
diagram�
• Then locate the front peg into the front access hole and
push in firmly�
• When locating the left side racks into the small oven or
grill ensure the pegs go into the top access holes�
setting the time
If you have purchased a model fitted with an electronic or
programmable timer, you
must
set the time of day before you
can operate your appliance�
Electronic Clock
• After the appliance has been electrically connected
“12�00” will be displayed and the “clock” indicator will
flash.
• To set the time of day, press – or +. 5 seconds after
the last change, the “clock” indicator will disappear,
confirming the time has been set�
NoTe: The clock has a 24-hour display.
Programmable Controller (POR783 only)
• After the appliance has been electrically connected, the
set clock symbol and timer arrow will flash on the
clock display�
• To set the time of day, press – or +. 5 seconds after the
last change the timer arrow will disappear, confirming
the time has been set� Once the time has been entered,
the clock advances minute by minute�
NoTe: The clock has a 24-hour display.
catalytic liners
(on selected models)
Catalytic liners are coated with a specially formulated enamel
coating� This porous coating enables the “self cleaning”
process - see page 26 for more details� Catalytic liners must
be installed first but you can omit them, if you wish, with no
effect to cooking performance� Their sole purpose is to make
oven cleaning easier�
• The catalytic liners will attach to each side of your oven.
There will be a left hand and right hand version� This is
marked on the panel�
• Position the first liner as per the diagram. The black, shiny
side of the liner should be facing the oven wall, the hooks
pointing down and the word ‘LH’ positioned to the top
rear portion of the oven� The right hand side will be a
mirror image of this�
• Line the hooks up with the slots provided in the oven wall,
push them in and then allow the liner to slide down to its
final position�
• The access hole for the side racks should be visible when
the liner is correctly positioned - see diagram�
