Westinghouse iGen1200 User Manual Download Page 6

6 | Westinghouse Portable Power

DANGER

Never use the inverter in a location that is wet or damp. Never expose the inverter to rain, snow, 

water spray or standing water while in use. Protect the inverter from all hazardous weather conditions. 

Moisture or ice can cause a short circuit or other malfunction in the electrical circuit.

Never operate the inverter in an enclosed area. Engine exhaust contains carbon monoxide. Only

operate the inverter outside and away from windows, doors and vents.

WARNING

Voltage produced by the inverter could result in death or serious injury.

•  Never operate the inverter in rain or a flood plain unless proper precautions are taken to avoid being 

subject to rain or a flood.

•  Never use worn or damaged extension cords.

•  Always have a licensed electrician connect the inverter to the utility circuit.

•  Never touch an operating inverter if the inverter is wet or if you have wet hands.

•  Never operate the inverter in highly conductive areas such as around metal decking or steel works.

•  Always use grounded extension cords. Always use three-wire or double-insulated power tools.

•  Never touch live terminals or bare wires while the inverter is operating.

•  Be sure the inverter is properly grounded before operating.

WARNING

Gasoline and gasoline vapors are extremely flammable and explosive under certain conditions.

•  Always refuel the generator outdoors, in a well-ventilated area.

•  Never remove the fuel cap with the engine running.

•  Never refuel the inverter while the engine is running. Always turn engine off and allow the generator 

to cool before refueling.

•  Only fill fuel tank with gasoline.

•  Keep sparks, open flames or other form of ignition (such as match, cigarette, static electric source) 

away when refueling.

•  Never overfill the fuel tank. Leave room for fuel to expand. Overfilling the fuel tank can result in a 

sudden overflow of gasoline and result in spilled gasoline coming in contact with HOT surfaces. 

Spilled fuel can ignite. If fuel is spilled on the inverter, wipe up any spills immediately. Dispose of rag 

properly. Allow area of spilled fuel to dry before operating the inverter.

•  Wear eye protection while refueling.

•  Never use gasoline as a cleaning agent.

•  Store any containers containing gasoline in a well-ventilated area, away from any combustibles or 

source of ignition.

•  Check for fuel leaks after refueling. Never operate the engine if a fuel leak is discovered.

WARNING

Never operate the inverter if powered items overheat, 

electrical output drops, there is sparking, flames or smoke 

coming from the inverter, or if the receptacles are damaged.

Never use the inverter to power medical support equipment.

Always remove any tools or other service equipment used 

during maintenance from the inverter before operating.

NOTICE

Never modify the inverter.

Never operate the inverter if it 

vibrates at high levels, if engine 

speed changes greatly or if the

engine misfires often. Always 

disconnect tools or appliances 

from the inverter before starting.

GENERAL SAFETY RULES

SAFETY

Summary of Contents for iGen1200
































Reviews: