Westinghouse iGen1200 User Manual Download Page 20

20 | Westinghouse Portable Power

5.  Wash the foam air filter element by submerging the 

element in a solution of household detergent soap 

and warm water. Slowly squeeze the foam to thor-

oughly clean.

NOTICE

NEVER twist or tear the foam air filter element 

during cleaning or drying. Only apply slow but firm 

squeezing action.

6.  Rinse in clean water by submerging the air filter  

element in fresh water and applying a slow  

squeezing action (see Figure 18).

Figure 18 

NOTICE

Never dispose of soap cleaning solution used to 

clean the air filter by dumping the solution into 

a sewer, on the ground, or into ground water or 

waterways. Always be environmentally responsible.

Follow the guidelines of the EPA or other 

governmental agencies for proper disposal of 

hazardous materials. Consult local authorities or 

reclamation facility.

7.  Dispose of used soap cleaning solution properly.
8.  Dry the air filter element by again applying a slow firm 

squeezing action.

9.  Return the air filter element to its position in the air 

cleaner housing.

10. Install the air cleaner cover, making sure the tabs lock 

into place.

11. Install the engine service panel.

MAINTENANCE 

DRAINING THE FLOAT BOWL

1.  Remove the engine service panel to access the 

carburetor.

2.  Locate the clear plastic hose from the float and place 

a suitable container under it to catch the drained fuel 

(see Figure 19).

3.  Loosen the float bowl drain screw (see Figure 19) 

until fuel is seen draining from the float bowl.

fuel pan

Fuel Drain Hose

Float Bowl Drain Scr

ew

Figure 19: Loosen float bowl screw

4.  Allow fuel to drain into the container, and then tighten 

the float bowl drain screw.

NOTICE

Never dispose of fuel by dumping fuel into a sewer, 

on the ground, or into groundwater or waterways. 

Always be environmentally responsible. Follow the 

guidelines of the EPA or other governmental agencies 

for proper disposal of hazardous materials. Consult 

local authorities or reclamation facility.

5.  Install the engine service panel.

 

Summary of Contents for iGen1200
































Reviews: