background image

Lit. No. 27554, Rev. 08

3

August 1 , 2006

27550

PERSONAL SAFETY

• Remove ignition key and put the vehicle in park or in

gear to prevent others from starting the vehicle
during installation or service.

• Wear only snug-fitting clothing while working on

your vehicle or snowplow.

• Do not wear jewelry or a necktie, and secure long

hair.

• Wear safety goggles to protect your eyes from

battery acid, gasoline, dirt, and dust.

• Avoid touching hot surfaces such as the engine,

radiator, hoses, and exhaust pipes.

• Always have a fire extinguisher rated BC handy, for

flammable liquids and electrical fires.

HYDRAULIC SAFETY

• Always inspect hydraulic components and hoses

before using. Replace any damaged or worn parts
immediately.

• If you suspect a hose leak, DO NOT use your hand

to locate it. Use a piece of cardboard or wood.

SAFETY PRECAUTIONS

Improper installation and operation could cause
personal injury and/or equipment and property damage.
Read and understand labels and the 

Owner’s Manual

before installing, operating, or making adjustments.

 CAUTION

Refer to the Kit Selection Guide/Selection List
for minimum vehicle recommendations and
ballast requirements.

 WARNING

Do not exceed GVWR or GAWR including
blade and ballast. The rating label is found on
driver-side vehicle door cornerpost.

 WARNING

Keep hands and feet clear of the blade and
A-frame when mounting or removing the
snowplow. Moving or falling assemblies could
cause personal injury.

 WARNING

Remove blade assembly before placing
vehicle on hoist.

 WARNING

Lower blade when vehicle is parked.
Temperature changes could change hydraulic
pressure, causing the blade to drop
unexpectedly or damaging hydraulic
components. Failure to do this can result in
serious personal injury.

 WARNING

The driver shall keep bystanders clear of the
blade when it is being raised, lowered, or
angled. Do not stand between the vehicle and
the blade or within 8 feet of a moving blade. A
moving or falling blade could cause personal
injury.

 CAUTION

To prevent accidental movement of the blade,
always turn the ON/OFF switch to OFF
whenever the snowplow is not in use. The
control indicator light will turn off.

 WARNING

Hydraulic fluid under pressure can cause skin
injection injury. If you are injured by hydraulic
fluid, get medical attention immediately.

Summary of Contents for 27550

















Reviews: