Western Digital Ultrastar Data102 Installation Manual Download Page 77

Page: 77 / 79

Installation Guide

5. Installation

5.4 SAS Cabling

Figure 54:

Service Loop Diagram

Table 17:

Service Loop Lengths

Cable Identifier

Length to First Basket Clip

16 in / 406 mm

18 in / 457 mm

19 in / 483 mm

22 in / 559 mm

23 in / 584 mm

5.4

SAS Cabling

The Ultrastar Data102 can use passive cables that are limited to 3m or less, or active cables of any length for

SAS connections to the host. Active cables must be used for Ultrastar Data102 to Ultrastar Data102 daisy

chaining connections. All approved passive and active SAS cables are listed in the following table.

Note:

MegaRAID adapters do not support the use of active SAS cables. If your configuration

requires the use of MegaRAID adapters, passive cables must be used.

Summary of Contents for Ultrastar Data102
















































































Search results

Summary of Contents for Ultrastar Data102

Reviews:

Related manuals for Ultrastar Data102

Brands by name

Popular brands

Western Digital Ultrastar Data102, Installation Manual

Search results

Summary of Contents for Ultrastar Data102

Reviews:

Related manuals for Ultrastar Data102

Brands by name

Popular brands