background image

17

6641-2222

Getting Started

This product runs Westermo Operating System (WeOS) which provides several  
management tools that can be used for configuration of the unit.

•  IPConfig tool  

This is a custom Westermo tool used for discovery of attached Westermo units.

• Web  

Configuration of the unit using the web browser. 

•  CLI

 

Configuration of the unit via the Command Line Interface.

If the computer is located in the same subnet as the switch you can easily use a web 
browser to configure the unit. Within the web you can configure most of the available 
functions. 
For advanced network settings and more diagnostic information, please use the CLI. 
Detailed documentation is available in the chapter 

The Command Line Management 

Tool

 in the WeOS management guide.

Factory default  

IP address:

 

192.168.2.200

 

Netmask:

 

255.255.255.0

 

Gateway:

 

Disabled

Note!

 If you are not sure about the subnet – consult your network administrator.

Configuration

Configure the unit via Webbrowser 

The unit can easily be configured via a Web browser.  
Open the link http://192.168.2.200 in your web browser, and you will be prompted with  
a Login screen, where the default settings for Username and Password are:

Username:

 admin 

Password:

 westermo

Once you have logged in, you can use the extensive integrated help function describing 
all configuration options. Two common task when configuring a new switch is to assign 
appropriate IP settings, and to change the password of the admin account.  
The password can be up to 64 characters long, and should consist of printable ASCII 
characters (ASCII 33-126); 'Space' is not a valid password character.

Note!

 Version of IP Config tool must be 10.4 or higher.

Summary of Contents for RedFox





















Reviews: