background image

5

6651-2231

General

This unit is intended for use in Zone 2 hazardous location only.

Marking

     II 3 G  
Ex nA IIC T4 Gc 
SPECIAL CONDITION
WARNING – DO NOT SEPARATE WHEN ENERGIZED

ATEX Information (Applicable for ODW-720-F2 Ex only)

Indicate that this unit complies with relevant European standards that are  
harmonised with the 94/9/EC Directive (ATEX).

II

Equipment group II. 
This unit can be installed in all places with an explosive gas atmosphere other 
than mines susceptible to firedamp

3

Equipment category 3.  
A category is the classification according to the required level of protection. 
This unit ensures the requisite level of protection during normal operation and 
is intended for use in areas in which explosive atmosphere caused by gases, 
vapours, mists, or dust mixtures are unlikely to occure or, if they do occure, are 
likely to do so only infrequently and for a short periode only.

G

Indicates protection concerning explosive atmospheres caused by gases,  
vapours or mists (G).

Ex

Indicates that this unit is in conformity with relevant European Ex standard(s).

nA

Type of protection used. 
This unit is a non-sparking device "nA" which is constructed to minimize the 
risk of occurence of arcs or sparks capable of creating an ignition hazard during 
conditions of normal operation.

IIC

Gas group, a typical gas i hydrogen.

T4

Temperature class T4 (T4 = 135°C). 
This unit is classified in accordance with its maximum surface temperature 
(external and internal).

Gc

Equipment protection level Gc (EPL Gc). 
Equipment for explosive gas atmospheres, having a "enhanced" level of protec-
tion, which is not a source of ignition in normal operation and which may have 
some additional protection to ensure that it remains inactive as an ignition 
source in the case of regular expected occurences. EPL Gc are analogous to the 
ATEX Categories (Category 3 G = EPL Gc).

SPECIAL 

CONDITION

This unit has a special condition of use. 
The special condition for safe use contains safety related information that is 
necesarry for the correct installation and safe use.

Summary of Contents for ODW-720-F2

























Reviews: