background image

6

11

3.

Press a 1 1/2Ó Square Inner Cap (4) into each end of
the stabilizer on the Front Leg (37). 

Attach the Bench Frame (8) to the bracket on the
Front Leg (37) with a 5/16Ó x 2 1/4Ó Bolt (1) and a
5/16Ó Nylon Locknut (7). 

Do not overtighten the

Nylon Locknut; you must be able to pivot the
Front Leg.  

Insert a 5/16Ó x 2Ó Carriage Bolt (33) through the
Bench Frame (8) and tighten a Locking Knob (34)
onto the Carriage Bolt. Insert a Small Locking Clip
(16) into the indicated hole.

33

37

16

7

1

4

34

4

8

3

4.

Attach the Bench Frame (8) to the bracket on the
crossbar of the ÒHÓ-Frame (5) with a 5/16Ó x 2 1/4Ó
Bolt (1) and a 5/16Ó Nylon Locknut (7). 

Do not over-

tighten the Nylon Locknut; you must be able to
pivot the Bench Frame.

Insert a 5/16Ó x 2Ó Carriage Bolt (33) down through
the crossbar of the ÒHÓ-Frame (5) and the tab on the
Bench Frame (8). Tighten a Locking Knob (34) into
the Carriage Bolt. 

Insert a Small Locking Clip (16) into the indicated hole.

1

16

8

Tab

7

5

33

34

4

THE FOUR BASIC TYPES OF WORKOUTS

Muscle Building

The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the inten-
sity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways: 
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets per-

formed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions). 

The proper amount of weight for each exercise obvi-
ously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.  

Toning

You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.  

Weight Loss

To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets. 

Cross Training

Many people desire a complete and well-balanced fit-
ness program, and cross training is a very efficient
way to accomplish this. One example of a balanced
program is:
¥ Plan weight training workouts on Monday,

Wednesday and Friday. 

¥ Plan 20 to 30 minutes of aerobic exercise, such as

cycling or swimming on Tuesday and Thursday. 

¥ Rest from both weight training and aerobic exercise

for at least one full day each week to give your body
time to regenerate. 

The combination of weight training and aerobic exer-
cise will reshape and strengthen your body plus
develop your heart and lungs. 

PERSONALIZING YOUR EXERCISE PROGRAM

Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very impor-
tant to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your bodyÕs sig-
nals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.

WARMING UP

Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.

WORKING OUT

Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
the most. To give balance and variety to your work-
outs, vary the exercises from session to session. 

Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.  

EXERCISE FORM

You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. Refer to the muscle chart on the
next page to find the locations of the muscles. 

The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath. 

Exercise Guidelines

5.

Attach the Left Barbell Hook (14) to the left side of
the ÒHÓ-Frame (5) with a 5/16Ó Nylon Locknut (7). 

Attach the Right Barbell Hook (38) to the right side
with a 5/16Ó Nylon Locknut (7).

5

Upright

38

7

14

5

Summary of Contents for Bench 300









Reviews: