background image

8

Technical Data

3.1 Spot Diameter

Range

30 mm

120 mm

200 mm

Spot diameter

9 mm

7 mm

10 mm

Table 1

Range

40 mm

80 mm

120 mm

Spot diameter

2,5 mm

1,5 mm

1 mm

Table 2

3.2 Switching Frequency / Response Time

The switching frequency and the response time are depending on 2 settings: operating mode and switching 
outputs. The following values result according to the setting:

Operating Mode

Outputs

2 independent switching outputs

1 switching output

Switching Frequency (Standard Mode)

100 Hz*

1000 Hz

Response Time (Standard Mode)

5 ms*

0,5 ms

Switching Frequency (Interference-free Mode)

50 Hz

500 Hz

Response Time (Interference-free Mode)

10 ms

1 ms

*preset configuration

Table 3

3.2.1 Switching Distance Deviation
Typical characteristic curve based on Kodak white (90 % remission).

P1KH016, P1KH024 

 

 

P1KH017, P1KH031

30

60

90

120

150

180

210

  -3

  0

  -6

 -9

 -12

 -15

Sr/mm

dSr/mm

P1KH

 

P1KH

30

40

50

60

70

80

90

100 110 120

-10

-8

-6

-4

-2

0

Sr/mm

dSr/m

m

Sr = Switching Distance 
dSr = Switching Distance Change 
Black 6 % remission  
Grey 18 % remission

Summary of Contents for P1KH Series



















Reviews: