Wen 61741 Manual Download Page 14 | Manualshive

Page: 14 / 16

Wen 61741 Manual Download Page 14

14

WARNING: Remove nails from magazine and disconnect the air supply before performing any maintenance.

Routine lubrication of the tool is required for best performance. Oil added through the airline connection will
lubricate internal parts. An automatic airline oilier is recommended but oil may be added manually before
every operation or after about 1 hour of continuous use. Only a few drops of oil at a time are necessary. Too
much oil will collect inside the tool and be blown out during the exhaust cycle. ONLY USE PNEUMATIC
TOOL OIL. Do not use detergent oil or additives, as these lubricants will cause accelerated wear to the seal in
the tool.

Dirt and water in the air supply are major causes of pneumatic tool wear. Use a filter/oiler for better perfor-
mance and longer lifetime for your tool. The filter must have adequate flow capacity for the specific applica-
tion. Consult the manufacturer's instructions for proper maintenance of your filter. Keep tools clean for better
and safer performance. Use nonflammable cleaning solutions only if necessary (CAUTION: Such solutions
may damage O-ring and other tool parts). DO NOT SOAK THE TOOL.

MAINTENANCE

«
...
12
13
14
15
16
»

Summary of Contents for 61741

















Reviews:

No comments