background image

WARNING:

 Check to make sure that all accessories are assembled correctly and securely on the ro-

tary tool. Do not use if any accessory or part is loose or damaged.

INSTALLING SANDING BANDS (Fig. 2)

Loosen the screw on the top of the sanding drum using the end of 
the included wrench to contract the width of the drum. Slide the 
sanding band onto the sanding drum. Fully tighten the screw to 
expand the width of the sanding drum to hold the sanding band 
in place. Make sure the sanding drum is sufficiently expanded to 
secure the band during use. If sanding band is loose on the drum, 
it may fly off during operation and cause injuries.

INSTALLING FELT POLISHING ACCESSORIES (Fig. 3)

Thread the felt polishing accessory straight down onto the tip of 
the screw mandrel. The accessory must be threaded all the way 
down to touch the collar of the screw mandrel.

INSTALLING WHEEL/DISC ACCESSORIES (Fig. 1)

Loosen and remove the screw at the top of the small screw man-
drel. Remove the top red ring from the screw and slide the wheel 
or sanding disc above the bottom red ring (ensure the abrasive 
side of the disc is facing up for sanding disc). Slide the top red 
ring above the wheel/disc, so that there is one red ring on each 
side of the wheel. Reattach the screw onto the mandrel to secure 
the wheel/disc in place. 

INSTALLING ROTARY TOOL BITS (Fig. 4)

1. Switch off and unplug the tool before making any adjustments.

2. Hold down the spindle lock button (Fig. 4 - 1) and rotate the 
collet nut (Fig. 4 - 2) until the spindle lock engages.

3. Using the included wrench, loosen and remove the collet nut 
by turning it counterclockwise. Release the spindle lock button.

4. An 1/8" collet is pre-installed inside the tool. Three collet sizes 
are included with your rotary tool as accessories: 1/8", 3/32" and 
1/16". 

Select the suitable collet to match the spindle diameter of your 
desired rotary tool bit. Thread the selected collet onto the spin-

WARNING:

 To avoid injury from accidental startups, always ensure that the tool is switched OFF and 

unplugged from the power supply before making adjustments or changing accessories.

dle and screw the collet nut back on, but do not tighten all the way.

5. Fully insert the rotary bit into the spindle hole through the collet nut and collet. Press down the spindle lock 
button and fully tighten the collet nut using the included wrench. Pull on the rotary tool bit to check that it is 
firmly secured inside the tool. 

Fig. 4

Fig. 1

Small Screw Mandrel

Screw Mandrel

Sanding Disc or 

Cut-Off Wheel

Felt Polishing 

Wheel/Tip

Sanding Drum 

Mandrel

Sanding Band

Fig. 2

Fig. 3

ASSEMBLY & ADJUSTMENTS

1

2

12

Summary of Contents for 23114



















Reviews: