background image

 

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS

Notes emphasize information and/or provide additional information to assist the user.

Caution messages appear before procedures that could result in damage to equipment if not observed.

Warning messages appear before procedures that could result in personal injury if not observed.

This manual is intended to be used as a basic installation and operation guide for the Welker Relief Valves, RV-1, RV-2, RV-2CP, and RV-3. For comprehensive 
instructions, please refer to the IOM Manuals for each individual component. A list of relevant component IOM Manuals is provided in Appendix A of this manual.

The information in this manual has been carefully checked for accuracy and is intended to be used as a guide for the installation, operation, and maintenance of 
the Welker equipment described in this manual. Correct installation and operation, however, are the responsibility of the end user. Welker reserves the right to make 
changes to this manual and all products in order to improve performance and reliability.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

- Save these instructions for local inspector's use.

IMPORTANT

- Observe all governing codes and ordinances.

Note to Installer

 - Leave these instructions with the end user.

Note to End User

 - Keep these instructions for future reference.

Installation of this Relief Valve is of a mechanical nature.

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the warranty.

If you received a damaged Relief Valve, please contact a Welker representative immediately.

Phone:

      281.491.2331

Address:

 13839 West Bellfort Street

Sugar Land, TX  77498

SAFETY

3

IOM-033

MODELS: RV-1, RV-2, RV-2CP, and RV-3

REV: F

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Summary of Contents for RV-1
















Reviews: