Weinzierl 5326 Operation And Installation Manual Download Page 35

Page: 35 / 36

Seite 35/36

12 Battery information

BATTERY WARNING

▪

Do not ingest battery, Chemical Burn Hazard.

▪

This product contains a coin cell battery. If the coin cell battery is swallowed, it can cause

severe internal burns in just 2 hours and can lead to death.

▪

Keep new and used batteries away from children.

▪

If the appliance is not permanently installed in the holding frame, keep the product away

from children.

▪

If you think batteries might have been swallowed or placed inside any part of the body,

seek immediate medical attention.

▪

Improper handling of batteries can result in explosion, fire or chemical burn due to

leakage.

▪

Do not heat or throw batteries into fire.

▪

Do not reverse polarity, short-circuit or recharge batteries.

▪

Do not deform or disassemble batteries.

▪

Replace batteries only with an identical or equivalent type.

DISPOSAL OF BATTERIES

▪

Remove empty batteries immediately and dispose of in an environmentally friendly

manner.

▪

Do not throw batteries into household waste.

▪

Consult your local authorities about environmentally friendly disposal.

▪

According to statutory provisions, the end consumer is obligated to return used batteries.

Summary of Contents for 5326





































Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands

Weinzierl 5326, Operation And Installation Manual

Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands