Weinzierl 5326 Operation And Installation Manual Download Page 4

Page: 4 / 36

Seite 4/36

2.1 KNX programming mode

The KNX programming mode is activated/deactivated either by pressing the recessed KNX
programming button

❷

or by simultaneously pressing the buttons

❸

and

❺

When the programming mode is active, the programming LED

❷

lights up red.

The operation of the programming mode on the front can be activated/deactivated in the ETS® on
page general settings.

2.2 Status display

Summary of the states of the programming LED

❷

Summary of the states of LED KNX

❼

Summary of the states of LED EnOcean

❽

The KNX RF / ENO Push Button 440

secure

is unidirectional in normal operation, and bidirectional

only during programming mode. Therefore, the programming mode must be activated before

downloading the ETS configuration (LED

❷

lights red).

LED Status

Meaning

LED lights red

Programming mode is active.

LED blinks red (fast)

Programming mode is not active.
The device is not properly loaded
e.g. after an interrupted download.

LED blinks red (slow)

The device is awake e.g. when connected to USB.

LED flashes 1x red

After button press (KNX mode).

LED flashes 1x red (all 5 s)

Low battery voltage (< 2.6 V).

LED is off

The device is in sleep mode.

LED Status

Meaning

LED flashes green

The device indicates a KNX communication, e.g. when sending
telegrams or during an active ETS download.

LED Status

Meaning

LED flashes green

The device indicates an EnOcean communication, e.g. when sending
telegrams.

Summary of Contents for 5326





































Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands

Weinzierl 5326, Operation And Installation Manual

Search results

Summary of Contents for 5326

Reviews:

Related manuals for 5326

Brands by name

Popular brands