manualshive.com logo in svg

Weil-McLain WM97+110, Manual, Page: 71 / 132

Share
Download
Weil-McLain WM97+110 Manual Download Page 71

Part number 550-142-085/0712

– 71 –

WM97+ 

gas

-

fired

 

water

 

boiler

 — 

Boiler Manual

ESSENTIAL settings

 

THE CONTROL SETTINGS LISTED BELOW MUST BE MADE BEFORE STARTING THE BOILER

. Failure 

to comply could result in incorrect operation of the boiler, causing possible severe personal injury, death or sub-
stantial property damage.

 

THE CONTROL SETTINGS LISTED BELOW SHOULD BE MADE BEFORE STARTING THE BOILER

. These 

settings provide information about boiler start-up and service. This information will help reduce troubleshooting 
time and inform technicians working on the equipment about boiler history.

 

CWH Installations — 

Follow all instructions in the CWH manual to verify that the mixing valve is installed and 

operational before proceeding further with the installation. Failure to correctly install the mixing valve and all 

necessary temperature regulating devices in the system could result in severe personal injury or death.

Step 1 

Read about menu access and navigation 
on page 72. 

Step 2 

Turn OFF power to the boiler. 

Step 3 

Turn off gas supply to the boiler by closing 
the boiler’s manual gas valve. 

Step 4 

Disconnect thermostat input wires to the 
boiler at the low voltage terminal block.

Step 5 

Turn ON power to the boiler. Turn boiler 
ON/OFF switch to ON.

Step 6 

Navigate to the BOILER SETTINGS / 
BOILER MODEL screen.

Step 7 

Read the boiler model shown on the dis-
play.

  If the boiler model number shown does NOT 

match the boiler, the selection MUST be changed 

to the correct model number. Failure to comply 

could result in severe personal injury, death or 

substantial property damage.

Step 8 

Navigate to the BOILER SETTINGS / 
HIGH ALTITUDE screen.

Step 9 

If the boiler is installed at altitude above 
5,500 feet, the selection must be changed 
to YES.

  If the boiler is installed at altitude above 5,500 

feet, the high altitude selection MUST be changed 

to 

YES

. Failure to comply could result in severe 

personal injury, death or substantial property 

damage.

Step 10 

Continue with recommended settings 
below.

Step 1 

Navigate to the CONTRACTOR MENU / 
SET DATE AND TIME screen.

Step 2 

Enter current date and time by accessing 
each screen and setting the data.

 

POWER OUTAGES

 — The date and time infor-

mation will be saved for brief power interrup-

tions. For interruptions longer than 30 minutes, 

the date and time information will be lost.

Step 3 

Navigate to the CONTRACTOR MENU / 
MAINTENANCE INFO screen.

Step 4 

Verify boiler model is shown correctly.

Step 5 

Input contractor name, phone, boiler CP#, 
installed date and interval setting. The in-
terval setting is the time for a maintenance 
reminder to appear on the display. Press 
RESET REMINDER to reset the dates.

Step 6 

Turn off power to the boiler. Turn boiler ON/
OFF switch to OFF. Reconnect thermostat 
input wires on low voltage terminal strip.

Step 7 

To adjust controls settings, proceed to the 
next page. If settings are complete, pro-
ceed with start-up on page 85.

Summary of Contents for WM97+110





































































































































Reviews:

No comments