Weil-McLain WM97+110 Manual Download Page 43

Page: 43 / 132

Part number 550-142-085/0712

– 43 –

WM97+

gas

fired

water

boiler

—

Boiler Manual

System piping

(continued)

Figure 47

WM97+70/110

Zone valve zoning — direct connection

(boiler primary/secondary by-pass valve CLOSED)

Figure 48

The system must meet the following

requirements when applying Figure 47

Boiler model

WM97+70 WM97+110

MAIN line size (inches)

[

]

BRANCH line size
(inches) [

]

Total FLOW, GPM

6.3

9.9

Boiler internal circulator:
TACO model

007-IFC

0015-IFC

Circulator HEAD (feet)
available to the system

5.0

6.5

Finned-tube baseboard (¾”) applications:

Minimum NUMBER of
circuits

Maximum FLOW per
circuit, GPM (20°F
temperature drop)

3.5

4.0

Maximum LOAD per
circuit, MBH

Maximum FEET
of FINNED TUBE
BASEBOARD per loop
(@ 600 BTUH per foot)

— Maximum circuit

length, feet (see L–1, L–2
and L–3 in Figure 47)

102

105

Legend — Figure 46, page 42 & Figure 47, page 43

WM97+70 or 110 boiler

Indirect water heater, if used

(for CWH installations, refer

to the Weil-McLain CWH

manual)

Relief valve, supplied with

boiler, field piped — MUST

be piped to boiler supply
connection — see page 13 for

information

Relief valve piping to drain —

see page 37

DHW circulator

Isolation valves

Supplementary expansion

tank, diaphragm type, if used

Air separator

Flow/check valve

Purge/drain valves (one drain

valve is supplied loose with the

boiler)

Boiler circulator, with inte-

gral flow/check valve, factory

installed in boiler

Zone valves

Primary/secondary by-pass

valve — see page 38 for infor-

mation — CLOSED: Boiler

circulator provides system

flow

Make-up water supply

By-pass pressure regulator,

RECOMMENDED for zone

valve systems unless other

provision is made

Backflow preventer, if used

Pressure reducing valve, if

used

Internal expansion tank,

diaphragm-type

Quick-fill valve, if used

DHW boiler water supply

connection, when used — see

page 13 for information

DHW boiler water return

connection, when used — see

page 13 for information

Pressure/temperature

gauge, supplied with boiler,

field piped

Heating circuits

Additional heating circuits, if

any

= Items supplied with boiler

— all other items supplied by

installer

DHW refers to an indirect-fired domestic hot

water storage tank. CWH refers to a Weil-
McLain Companion Water Heater.

Summary of Contents for WM97+110





































































































































Search results

Summary of Contents for WM97+110

Reviews:

Weil-McLain WM97+110, Manual, Page: 43 / 132

Search results

Summary of Contents for WM97+110

Reviews: