background image

Stripping and crimping machine 

 

Crimpfix 2.5 M  

08-09-19-DK-Operating Manual_gb.doc / 2008-09-19

  

17 

11.1 Error 

messages 

The error messages are shown on the display. The error messages are deleted by pressing key 

E

 

Code Fault 

Elimination 

Flashe. 

Saving or loading error 

RS485-TO Timeout 

interface 

Turn machine off and on or call the service. 

S.motore 

Stepping motor at the limit stop or 
blocked or timeout 

Turn the machine off an on and choose the program 
again. 

Curr.e. 

Current to high 
Machine is rough-running or blocked
 

3x 

   M.Motor 

E

 5s  Confirm 

 manual operation 

or 

 Move carefully stepwise forwards or backwards 

until the feeding funnel and the magazine are removable. 

C

  

Starting position 

Insert feeding funnel and fix it. 

E

 

Exit and back to the operating menu 

Insert the magazine. 

Start=0 Wrong 

triggering 

The starting switch S1 is activate 
short. 

Remove magazine 
Press 

E

. The machine goes to the starting position. 

Insert the magazine. 
 
If you don’t remove the magazine, the right treatment of 
the ferrule can’t be guaranteed. 

Start=1 Start 

position 

error 

Starting switcis used 

Stop=1 Stop 

position=1 

End position not reached 

Stop=0 Stop 

position=0 

Too much time for one cycle 

3x 

   M.Motor 

E

 5s  Confirm 

 manual operation 

 

 

Press until the motor stops. 

C

  

Starting 

position 

E

  

Exit and back to the operating menu. 

Insert in the magazine. 

Trash=0 

No stripping waste container 

Insert the stripping waste container completely. 

Flap=0 

Flap open 

Close the flap. 

Service 

Message after 200 000 crimps 

The machine should be returned to the manufacturer for 
any necessary maintenance work. 

 
 

Summary of Contents for Crimpfix 2.5 M





















Reviews: