11
12. Set the Foot Plate (19) on the Top Tube (16)
and the Bottom Tube (17).
Finger tighten
four
M4 x 25mm Screws (60) through the Tubes into
the Foot Plate.
Do not tighten the Screws yet.
13. Slide the Lock Frame (11) onto the notched
bracket on the Leg Frame (10), and insert the
lower end of the Lock Frame into the slot in the
Foot Plate (19). Attach the Lock Frame with an
M10 x 75mm Button Bolt (57), two M10
Washers (68), two 16mm Spacers (46), and an
M10 Locknut (65) as shown.
Make sure that
the Button Bolt is inserted through the hole
in the lower end of the Lock Frame.
See step 12. Tighten the four M4 x 25mm
Screws (60).
Pull the Ankle Lock Assembly (33) upward and
pivot the Lock Frame (11) over the indicated
notch in the bracket on the Leg Frame (10).
Release the Ankle Lock Assembly and engage
the Lock Frame into the notch.
See the inset drawing.
Attach an M8 x 16mm
Button Bolt (61) and an M8 Locknut (72) to the
hole in the end of the bracket on the Leg Frame
(10).
12
60
16
17
19
60
13
Notch
33
11
10
19
57
46
Slot
68
68
65
46
61
10
72
14. Identify the two Rear Ankle Braces (34), which
have holes in the indicated locations.
Slide a Rear Ankle Brace (34) onto the Ankle
Brace Tube (18). Attach the Rear Ankle Brace
with two M4 x 15mm Screws (58).
Make sure
that the Screws are tightened into the indi-
cated holes in the Ankle Brace Tube.
Next,
press a 19mm Round Cap (45) into the Ankle
Brace Tube, and attach the Round Cap with an
M4 x 15mm Screw (58).
Attach the other Rear Ankle Brace (34) to the
Ankle Brace Tube (18) in the same way.
34
18
Holes
Holes
34
58
58
45
14
10
10. Apply a small amount of grease to an M10 x
95mm Button Bolt (73).
Pull the Long Adjustment Knob (37) out as far
as it will go. Insert the bracket on the Backrest
Frame (8) into the Top Cover (23). Next, attach
the Backrest Frame to the Center Frame
Extension (6) with the M10 x 95mm Button Bolt
(73) and an M10 Locknut (65). Then, engage
the Long Adjustment Knob into one of the holes
in the bracket.
See the inset drawing.
Attach an M8 x 16mm
Button Bolt (61) and an M8 Locknut (72) to the
hole in the end of the bracket on the Backrest
Frame (8).
6
23
Bracket
65
73
Grease
8
37
61
8
72
11.
See the left inset drawing.
Identify the Top
Tube (16), the Bottom Tube (17), and the Ankle
Brace Tube (18); the Tubes have different
lengths and holes in different positions.
Orient the Top Tube (16) and the Bottom Tube
(17) so that the largest holes are on top
(see
the right inset drawing),
and insert them into
the indicated holes in the Leg Frame (10).
Attach each Tube with an M4 x 15mm Screw
(58).
Orient the Ankle Brace Tube (18) as shown, and
insert it into the Leg Frame (10). Attach the
Ankle Brace Tube with two M4 x 15mm Screws
(58).
Make sure that the M4 x 15mm Screws (58)
are tightened into the holes in the bottoms
of the Tubes (16, 17, 18).
17
16
58
58
10
11
16
17
18
18
Holes
58
Holes
Largest holes
must be on top
17
16
10
