background image

Remote Serial HMI

E

ng
lis

h

3 CONTENT OF THE PACKAGE 

Upon receiving the product, check if the package 
contains:

 

„

Accessory in anti-static package.

 

„

RS485 (CFW100-CRS485) module.

 

„

3-m mini USB cable.

 

„

Installation, configuration and operation guide.

4 INSTALLATION OF THE ACCESSORY

The CFW100-KHMIR accessory is easily connected 
to the CFW100 frequency inverter by means of the 
plug-and-play concept. The procedures below must 
be observed for the proper installation and start-up:

1. With the inverter de-energized, remove the front

cover of the inverter shown in 

figure A.1 (a)

.

2. Connect the CFW100-CRS485 accessory (RS485

module) to the inverter as shown in 

figure A.1 (b)

. For 

further details, refer to the Installation, Configuration
and Operation Guide of the CFW100-CRS485
module.

3. Connect the cable to the CFW100-KHMIR and

CFW100-CRS485 as indicated in 

figure A.1 (c)

4. Energize the inverter and check that the display of the 

remote serial HMI shows the same indication as the 
inverter HMI. Otherwise, repeat items 1-4, checking 
the cable connections.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for CFW100 series














Reviews: