background image

DRIVE REACH OTR FLEET   

CELL SIGNAL BOOSTER

13

______

Safety Guidelines

 

Use only the power supply provided in this package.

 Use of a non-weBoost product may damage 

your equipment.

All inside panel and dome antennas must have at least 6’ of separation distance from all active users, 

and low profile antennas must have at least 1.5’ separation distance from all active users.  

Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the  

cell phone.

RF Safety Warning: Any antenna used with this device must be located at least 8 inches from  

all persons.

FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR 

WIRELESS PROVIDER, PLEASE SEE BELOW: 

Sprint:  

http://www.sprint.com/legal/fcc_boosters.html 

T-Mobile/MetroPCS:  

https://support.t-mobile.com/docs/DOC-9827 

Verizon Wireless:  

http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html 

AT&T:  

https://securec45.securewebsession.com/attsignalbooster.com/ 

U.S. Cellular:  

http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp

This is a CONSUMER device.

BEFORE USE, you 

MUST 

REGISTER THIS DEVICE with your wireless provider and have your 

provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers 

may not consent to the use of this device on their network. If you are unsure, contact your provider.

You 

MUST

 operate this device with approved antennas and cables as specified by the 

manufacturer

. Antennas 

MUST 

be installed at least 20 cm (8 inches) from any person.

You 

MUST

 cease operating this device immediately if requested by the FCC or licensed wireless 

service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls served by 

using this device.

BU-GDE000264-001-030220.indd   13

BU-GDE000264-001-030220.indd   13

3/2/2020   10:41:53 AM

3/2/2020   10:41:53 AM

Summary of Contents for DRIVE REACH OTR FLEET





















Reviews: