background image

Feel the drive

Water Heater

Installation documentation

WARNING!

Hazard warning:

Incorrect installation or repair of Webasto heating systems may cause a fire or result in the 
emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as 
a result.

Specialist company training, technical documentation, specialised tools and equipment are 
required to install and repair Webasto heating and cooling systems.
Only original Webasto parts must be used. For this, also see the catalog of air and water heat-
er accessories from Webasto.

NEVER attempt to install or repair Webasto heating or cooling systems if you have not 
successfully completed the company training and thereby acquired the required tech-
nical skills, or if you do not have access to the required technical documentation, tools 
and equipment needed to carry out correct installation and repairs.

ALWAYS follow all Webasto installation and repair instructions and observe all warnings.

The initial startup is to be executed with the Webasto Thermo Test Diagnosis.

Webasto does not accept any liability for defects and damage that are attributable to installa-
tion by untrained staff.

Ident. No.: 1303854F_EN

Fee Euro 10.00

© Webasto AG

Ford Focus / Focus C-MAX / Focus CC

Petrol

from Model Year 2004

For left-hand drive vehicles only

Thermo Top E

 Parking Heater

e1

00 0003

Summary of Contents for Thermo Top E





























Reviews: