4
Stand Wallbox
– Nut M8
– Washer M8
– Spring washer M8
■
■
Installation Instructions
X
X
Check the Scope of delivery on completeness and
damage.
– Do not install a damaged stand.
– Notify Webasto Customer Service in case of damage.
4 Installation
Observe the safety information provided in chapter 2.
In addition to these installation instructions follow and
comply with the local regulations relating to operation,
installation and environmental protection.
Install the stand only in combination with the applica-
tion of the Operating- and Installation instructions of the
Webasto Pure or Live charging stations
4.1 Required tools
Tool
Description
Torx screwdriver TX30
Mounting of the charging stations
Earth ground tester
Check resistance of the ground
connection.
Verify cables are potential-free.
Cabling tools
Making the ground connection.
General tools, drills,
drilling machine.
Mounting of the ground connec-
tion and mounting of the stand.
4.2 Location requirements
General
X
3
The intended location must fulfil all the requirements
mentioned in the Webasto Pure or Live Operating- and
Installation instructions.
X
3
In case the stand is installed close to a road or on a pub-
lic parking place, open or roofed, an adequate collision
guard / protector must be installed.
X
3
In case more than 1 stand will be installed next to each
other, the free space between two stands should be at
least 200 mm.
X
3
The surface must be fully flat.
NOTE:
Do not install the stand on asphalt. The stability of
the stand on asphalt is not guaranteed.
4.3 Concrete base
■
■
For a secure installation of the stand a concrete base is
recommended:
– The calculations, design and creation of the base are the
responsibility of the manufacturer of the concrete base.
– Water should not be collected at the base but should be
drained naturally.
■
■
The electrical supply cables must come out of the
concrete at the centre of the base and have an excess
length of at least 1500 mm.
■
■
The manufacturer of the base must take care of
adequate protection of the cables. Protections sleeves
should extend to at least 250 mm above the concrete.
■
■
A ground connection should be available.
– If a ground connection is not implemented, an earth
point can be made with help of an earth rod. In such
a case the earth rod should be positioned in the
centre of the base of the stand.
4.4 Installation of the stand on a concrete base
NOTE:
Dowels, screws and washers for mounting the stand
to the concrete are not part of the Scope of Delivery.
X
X
Position the stand over the cables. Make sure the cables
are in the centre of the stand.
X
X
Mark the position of the bore-holes on the concrete.
X
X
Remove the stand.
X
X
Drill the holes for dowels.
X
X
Insert the dowels in the bore holes. Make sure they are
level with the concrete.
The Webasto charging stations safety concept is
based on a power supply system that is grounded at
all times. The authorised electrician must ensure this
requirement during installation.
X
X
Do not install the stand if there is no ground
connection or a ground connection that does not
fulfils the requirements.
X
X
Provide a suitable cable lug M8 (Fig. 01; 6) to the
ground wire (Fig. 01; 3).
X
X
Connect the ground wire to the stud in the stand
housing with the M8 screw, spring washer, washer and
nut (Fig. 01; 1, 2, 4, 5) from the Scope of Delivery.
X
X
Make sure the ground connection fulfils the local
requirements for ground connections. Make sure the
resistance is lower than 0.1 Ω.
X
X
Thread the electrical cables (Fig. 02; 1), from the bottom
side up, through their respective feed-throughs.
X
X
Put the stand in the upright position.
X
X
Mount the stand with washers (Fig. 03; 2) and screws
(Fig. 03; 1).
X
X
Mount the Webasto Pure or Live charging
stations according the Webasto Pure or Live
Operating and Installation Instructions.
X
X
Use the washers of the Scope of Delivery of the
charging stations but use the screws of the Scope
of Delivery of the stand.
X
X
Use TX M6 x 25 screws for the top part of the
charging station.
X
X
Use TX M6 x 50 screws for the bottom part of the
charging station.
X
X
Install the cover on the stand by clipping it onto it.
NOTE:
Once the cover is installed,it is fixed on the stand and
cannot be removed again.
5 Maintenance, cleaning and repair
5.1 Maintenance
The stand does not require any maintenance.