background image

 

11 

 

 

Error code output on combination timer or control element 

 

If the system is fitted with a combination timer, when an error occurs an error 

code is displayed on the timer's screen until the heater has been properly 

repaired. 
The error code is output if the heater is fitted with a control element after an 

error has occurred by the switch- on indicator/error code indicator flashing. 

After a burst of fast flashes the error code will be displayed by a se- quence of 

long flashes, the number of which is shown in the table below. 

Error code  Meaning 

F 00* Control unit error 
F 01  No start (after 2 starting attempts)  
F 02  Flame failure (at least > 3) 
F 03  Undervoltage or overvoltage  
F 04  Premature flame recognition 
F 05  Flame monitor (petrol heater) interrupt or short circuit 
F 06  Temperature sensor interrupt or temperature sensor short circuit  
F 07  Metering pump interrupt or metering pump short circuit 
F08    Fan motor interrupt or fan motor short circuit or fan motor overload 

or blocked 

F 09  Glow plug interrupt or glow plug short circuit  

F 10  Overheating 
F 11* Overheating sensor interrupt or overheating sensor short circuit  
F 12* Heater unit lock-out 
F 14  Overheating sensor installed incorrectly / defective  
F 15* Defective controller / open or short circuit 
F 16** Exhaust temperature exceeded 
F 17** Exhaust gas temperature sensor defective  
F 18** Defective controller / open or short circuit 
F 19** Plausibility of sensors incorrect (exhaust / overheat sensor) 

If serious malfunctions such as overheating or failure occur, the 
heater will go into a locked state (F 12). This state can be reset 
by using the following heater lockout reset procedure. 

*Not used on EVO 40 and EVO 55 
** Not used on AirTop 2000ST and 2000STC 

Summary of Contents for Air Top Series















Reviews: