WCP GreyT Elevator V3 User Manual Download Page 35 | Manualshive

Page: 35 / 42

background image

GreyT Elevator V3 - User Guide

(Rev 1)

Page 35

Table of Contents

wcproducts.com

Step 24

Install the hex shaft with the cross drilled hole on the same side as the other polycord

pulleys.

Install the 1/2” ratcheting wrench on the opposite side and constrain it with a shaft

collar. When installing the wrench, ensure that when the shaft is turned

counter-clockwise from the wrench side that the wrench does not spin but ratchets. To

prevent the wrench from spinning, a hole may be drilled into the wrench to bolt it to the

carriage. Alternately, a bolt and spacer can be used for the wrench to rest against. Use a

zip-tie to constrain wrench.

Install a washer on the side with the cross drilled hole. Use a 1/4”-20 x 1/4”L bolt to hold

the washer on.

Note: Hex wrench and washer are NOT included� Recommended washer size is 1”OD or

larger�

«
...
33
34
35
36
37
...
»

Summary of Contents for GreyT Elevator V3











































Reviews:

No comments

Related manuals for GreyT Elevator V3

Brand: Datavideo Pages: 17

Brand: Balboa Pages: 74

Brand: Truweld Equipment Pages: 28

Brand: TradeQuip Pages: 9

Brand: Telwin Pages: 108

Brand: WAGO Pages: 20

ThermoPro G4 Series

Brand: Curtis Pages: 40

Brand: MOSA Weld Pages: 36

Brand: C.S.L. Pages: 27

Brand: zika Pages: 13

Brand: AMGO Hydraulics Pages: 40

Brand: Tuxedo Pages: 33

Brand: Gruetzner Pages: 41

Brand: Daihen varstroj Pages: 25

Brand: gala gar Pages: 28

Brand: Dometic Pages: 24

Brand: Thermal Dynamics Pages: 32

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands