WCP GreyT Elevator V3 User Manual Download | Manualshive

Page: 33 / 42

background image

GreyT Elevator V3 - User Guide

(Rev 1)

Page 33

Table of Contents

wcproducts.com

Step 22

Install the #25H chain and chain tensioner. Either the Spartan #25 Chain Tensioner

(WCP-0051) or the #25 Chain Turnbuckle (WCP-0247) are compatible with this setup.

The recommended spot for the tensioner is within the green circles. Other locations may

be used as well.

After both tensioners have been added and aligned with each other, use the chain clamp

plate and four #4-40 bolts per side to attach chain to the chain mounting block. Two

additional 1/8” roll pins may be added per side as well. This addition will help reduce the

load on the #4-40 bolts.

Note: For information on how to install the chain tensioners, refer to the manual on

their product page�

«
...
31
32
33
34
35
...
»

Summary of Contents for GreyT Elevator V3











































Reviews:

No comments

Related manuals for GreyT Elevator V3

Brand: Magmaweld Pages: 8

Brand: Magmate Pages: 20

Brand: Magliner Pages: 20

Brand: SMT Pages: 24

Brand: STAYER WELDING Pages: 56

Brand: Barton Pages: 36

SUPERIOR TIG 242

Brand: Telwin Pages: 108

ARCITECH WS2100

Brand: Campbell Hausfeld Pages: 36

Brand: Data Aire Pages: 100

Brand: Dino lift Pages: 121

Brand: WITTUR Pages: 47

Brand: Cattron Pages: 72

Brand: morse Pages: 5

Brand: Lincoln Electric Pages: 100

Brand: Lincoln Electric Pages: 152

Opto-Matic 30078

Brand: Trico Pages: 2

Brand: IFM Electronic Pages: 15

ARIA EVO H/V 170

Brand: Valsir Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands