Wayne P250AF Instructions Manual Download | Manualshive

Page: 18 / 26

background image

17

DIRECT SPARK IGNITION SINGLE ROD TROUBLESHOOTING INFORMATION

NOTE 1: BURNERS ARE NOT PRESET FROM THE FACTORY AND MUST BE ADJUSTED AT THE SITE.

NOTE 2: NEW GAS LINE INSTALLATIONS WILL HAVE AIR IN THE LINES AND REQUIRE SEVERAL IGNITION ATTEMPTS

TO PURGE ALL THE AIR FROM THE LINES.

NOTE 3: DO NOT ATTEMPT TO PERFORM ANY WORK ON THIS BURNER UNLESS THE FOLLOWING TOOLS ARE

AVAILABLE AND YOU ARE A CERTIFIED INSTALLER:

I . VOLT METER-VOLTS, OHMS, CONTINUITY
2. AMP METER-CLAMP TYPE
3. BURNER MANUAL
4. MANOMETER
5. BLADE SCREW DRIVERS
6. NUT DRIVERS
7. OPEN END WRENCHS
8. TAPE MEASURE

The Wayne Burner that you are attempting to troubleshoot has the following electrical 115 Volt Single phase components:

1. 115 volt Combustion Fan Motor w/End Switch
2. Fan Relay-24 volt coil side and 110 volt fan side
3. Honeywell Gas primary Control(24 VOLT)
4. Honeywell Gas Valve(24 VOLT)
5. 24 volt Transformer
6. Ignition Rod/Sensing Rod
7. Ignition Lead
8. T-T (24 VOLT) TERMINAL

«
...
16
17
18
19
20
...
»

Summary of Contents for P250AF



























Reviews:

No comments

Related manuals for P250AF

Brand: Napoleon Pages: 104

Brand: YOKOI KIKAI KOSAKUSHO Pages: 16

Brand: FMI Pages: 28

SureFire II HDHESI

Brand: Fireye Pages: 15

Brand: Napoleon Pages: 12

Brand: baltur Pages: 46

Brand: baltur Pages: 76

Brand: baltur Pages: 44

Brand: Dabos Pages: 29

Brand: baltur Pages: 124

Brand: baltur Pages: 92

Brand: baltur Pages: 60

Brand: Strend Pro Pages: 12

nutrichef PKSTIND52

Brand: Pyle Pages: 5

Brand: Bodum Pages: 48

Brand: Varmebaronen Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands